Dear Sir
We got the problem on DFU upload firmware, it always failed in second DFU . We must unpair the device at iOS setting panel. Before next DFU.
Here is the log data...
Hi All,
My requirement is to read the data from nRF51822 device that is connected to a bluetooth and bluetooth is connected to a system using a .Net application.
I have...
Hi everyone,
I'm using the nRF51822 (pca10000 Dongle + pca10005).
My plan is to send one byte over the radio.
I tried to use the SDK-Example as a template but it's...
Hi,
Is that possible to run the radio_test_example (\nRF51 SDK_v5.2.0.39364\Nordic\nrf51822\Board\nrf6310\radio_test_example) on the nRF51822EK? If yes, what modifications...
we also produced self PWM for ADC wave form testing. when we stop transmission, we will get good waveform out, but when we starting transmission, output waveform shape is...
Dear Support,
I have some troubles with the Evaluation Kit for nRF51822 :
I use the broad as a central role with S120_nrf51822_1.0.0_softdevice.hex and example...
Suppose a nRF9E5 transmitter is set for continuous transmission on a channel.
A nRF9E5 receiver listening on that channel:
finds carrier and sets CD
finds address...
Hi,
I'm trying to develop something for nrf52832 and was trying to use the s130 softdevice. Using Kiel uVision 5 i added all the necessary packs, but when I add s130 to...
Hi,
I have two devices and one host. When they are in close area both of them are pairing to one host. When I switch off host, both devices looks like paired to each other...
Having gotten through the hurdles of getting my IAR project to compile and run on Segger Embedded Studio, I am now seeing different behavior between the two IDEs while debugging...
Hello,
In my application (based on app_nus_uart example, with two NRF52832 boards), one of the cases is uploading/downloading files with sizes up to 10MBytes.
In my app...
Can someone explain the reasons/benefits of using the single vs dual bank BLE boot loader?
Actually, why isn't there a single bank BLE bootloader in the example project...
I have following code which should start the app_timer and blink the LED_1.
When flashed, the LED_0 turns on and I can see the "Started." log. But the LED_1 is not blinking...
Hello,
I use nrfutil to generate the dfu .zip file, the error log is listed below. what is the reason? the softdevice is s140. thanks.
>>nrfutil pkg generate --hw-version...
ble_app_uart_c_pca10056_s140 fails with an assertion - I have downloaded nRF5_SDK_14.2.0_17b948a. For the example project examples\ble_central\ble_app_uart_c\pca10056\s140...
Hi,
I am trying to write a 120 byte data through ble to raspberrypi from my android app(I increased the MTU to the required limit). But all I am able to transfer is first...
Hi Team
Let's assume, we have a provisioner (client) and several successfully provisioned servers in a mesh network. We now want to remove one of these servers from that...
Hello,
I am currently migrating from SDK12.2 with softdevice S132 V3 to SDK14 with softdevice S132 V5 and have a problem configuring device names larger than BLE_GAP_DEVNAME_DEFAULT_LEN...
I am using nrf52832_xxaa and I'm porting my device from SDK11 to 14.
I have found that new sections have been added in the linker file of the examples like sdh_soc_observers...
Hi,
I use SDK v13.0.0 with SD S132 and to debug my application I use UART0 on Putty.
When I use SPIS (0) (no BLE and no softdevice) alone I perform all functionalities...
