Suppose a nRF9E5 transmitter is set for continuous transmission on a channel.
A nRF9E5 receiver listening on that channel:
finds carrier and sets CD
finds address...
I will be deploying my nRF51822-powered devices into the field and the end user will not be able to have any physical access to, for example, power cycle the board. I need...
Hi,
We are using the ble_app_uart example in evaluation board to read data from some sensors and send it to the nRF UART V2.0 in Android 4.4. Every 20 ms I am trying to...
I am try this at nrf51_sdk_v6_0_0_43681\nrf51822\Board\nrf6310\s110\ble_app_hids_keyboard
Firt I connect to Android device and keep one whitelist.pp_addrs and one whitelist...
Hi,
Parameter uint8_t ble_gap_scan_params_t::filter is present in the documentation, but not implemented.
Checked for SDK 5.2.0 and 6.0.0.
devzone.nordicsemi.com...
After I get a Disconnected() event, I want to start scanning again, therefore try to call StartDeviceDiscovery() again.
IsDeviceDiscoveryOngoing was checked before.
The...
Hi,
How can i disable peer manager from the buttonless DFU example. if just disable the peermanager by removing the code and editing sdk file, its not working.
i am using...
Hi All,
I am working on BLE+SD card.I am getting following error:-
*** Using Compiler 'V5.06 update 4 (build 422)', folder: 'C:\Keil_v5\ARM\ARMCC\Bin'
Build target...
I have a app that stores some calibration information in flash (1 page at 0x7F000)
When I booted now I noticed it has replaced it with "DEADCODE" following some hex number...
SDK version 12.2 and SoftDevice 132 and Dev. Board 10040
I am trying to run the ble_app_beacon example with NRF52832 DK. I have imported the IAR project into Segger Studio...
Hi,
I bought the nRF52840 in april. The problem is that my iPad doesn't detect the nRF52840. Also, when Itry to upload a .hex file on it, the board tells me that the upload...
Engineerings, We are looking around to find a way to prove that the hex file burned into the device is really the result of the original source code. Is there any idea/way...
Hi Guys, I try to implements the ctrl-C/V for bluetooth HID keyboard. But from SDK, I can't figure out how to send two keys. Even I do not use buffer_enqueue/dequeue in order...
Hello,
I try to build mesh sdk for nrf52840 it gives me error on RTT
0> <t: 0>, main.c, 318, ----- BLE Mesh Light Control Client Demo -----
0> <t: 0>, main.c, 108, Initializing...
hi, In my setup, I have a 3.7 V battery divided down to the bandgap range using a 100k and 100k resistors, so the voltage at the ADC input is 3.7 * (100/200) = 1.85 V. I am...
Hi
I used "nRF5_SDK_for_Thread_v0.10.0 - cli sample code and try to test Thread command "diag"
when I type "diag" then it will show "diagnostics mode is disable".
...
I am working on a project which involves sending data from many beacons to many other beacons. To be more specific, I have two groups of beacons:
The first group consists...
I'm planning to use one of those beacon platforms:
www.ebay.com/.../352167746226
www.ebay.com/.../112493464451
for a close proximity positioning system now I'd like...
hi.
How do i do ble_app beacon advertisement to one device(Android phone) whose bluetooth address is known ?? I want that beacons should only be seen in nrf_connect app of...
