I will be deploying my nRF51822-powered devices into the field and the end user will not be able to have any physical access to, for example, power cycle the board. I need...
Hi,
We are using the ble_app_uart example in evaluation board to read data from some sensors and send it to the nRF UART V2.0 in Android 4.4. Every 20 ms I am trying to...
I am try this at nrf51_sdk_v6_0_0_43681\nrf51822\Board\nrf6310\s110\ble_app_hids_keyboard
Firt I connect to Android device and keep one whitelist.pp_addrs and one whitelist...
Hi,
Parameter uint8_t ble_gap_scan_params_t::filter is present in the documentation, but not implemented.
Checked for SDK 5.2.0 and 6.0.0.
devzone.nordicsemi.com...
After I get a Disconnected() event, I want to start scanning again, therefore try to call StartDeviceDiscovery() again.
IsDeviceDiscoveryOngoing was checked before.
The...
Hi, I wanted to ask a question regarding sending data.
I currently have external memory that will send out serial data (SPI) to the nordic microcontroller. I have saved...
Recently, I try to programme nRF51822 DK communicating with nRF2401e1 DK,unfortunately，which does not success. With setting radio configuration: TXPower,frequency channel...
Hi i am starter to nordic nrf52.....I have issue in storing the large array values it shows no space...how to increase the space to store array values...plzzzz. thank you
The only reference is an old one back in 2014, has standard JTAG boundary scan been implemented on the nRF51822? If not, is the JTAG interface used for programming only? Debugging...
Aim: I want broadcast ibeacon info in one broadcast packet, and broadcast ibeacon name at the next broadcast packet.
The broadcast packet data length is 30 bytes.
Q...
I am looking for some guidance as to the memory regions to reserve for the Bootloader hex if I pull it in via Segger Embedded Studio. I have the memory allocations for the...
I have a working application with TIMER1 setup to fire handler every 10us. I would like to add a 560us periodic event to enable/disable a PWM, so I add a little more code...
Hi,
Using the NRF52 DK PCA10040, I have built and loaded the KEIL temperature example project (C:\nRF52_SDK_0.9.2_dbc28c9\examples\peripheral\temperature\pca10036\arm5_no_packs...
hello ,
i want to know if there an example available that has both peripheral + Broadcaster role running at the same time , Broadcaster advertise the service in the peripheral...
Hi all Nordic developers,
I am currently working on an application using a sensor (the temperature sensor) on a Smart beacon kit, which must connect and send data to a...
Hi all,
What's the difference between the Beacon Transmitter Sample Application example given in nRF51 SDK and the beacon firmware provided in the beacon kit? Are there...
Hello,
I have a nRF 52 preview board (PCA10036) and would like to use ETM trace to enable the "execution profiling" in Keil v5.
After I enable the trace and ETM trace...
Hi,
I am facing hardfault when i try to enable low power in a ble application. i want to enable trace on my PCA10040 board to find out the cause of this hardfault. can...
Hi,
We are using our own custom nRF52832 based board, with revision B silicon however we are having trouble getting trace functionality to work.
Our code uses the Nordic...
Hi,
I am going to design a new product around nRF51422 and I am planning to buy the nRF51 DK but I am really confused about the sw I need for development and additional...
I found this recent Q&A very helpful on the topic of reading voltage on analog hardware pins via the ADC: devzone.nordicsemi.com/.../
In that Q&A, a helpful Nordic person...
