I have a central application and peripheral application that are based on the multilink-central/multilink-peripheral examples.
I've modified them to run on the PCA10001...
Hi All,
I'm using nRF24L01P for TX device and want to receive packet from nRF51822 RX device.
nRF24L01P TX device Register settings are as follows;
Reg.EN_AA=0x00...
I am trying to develop for some nRF51822 mbed boards, and I would like to use the S130 SD to enable both central and peripheral behaviour. The machine I'm using for development...
I'm using the nRF51822 eval kit
I have installed MCP but after starting I get pop-up: Master Control Panel has stopped working
In nRFgo Studio / Device manager pane...
the proximity example is running ok. but when I modify the length of the alert_level I have the following error on the server side that I am not understanding.
476;16:12...
Hi all,
I'm working with the nrf51422 and the nrf51822 and I was wondering what the current status of the over the air DFU system is.
I'm using SDK 6.0 and I managed...
nRF24l01+ at a transmitter module one time successful transmission show & after 1 sec failed also . if any doing programming with atmega32 ,please send code for TX & RX ....
Hello!
I am currently using a module called BLENano2 (nRF52832). SDK15.0.0 is used and the editor is "Segger Embedded Studio v4.16".
Finished writing the program that...
Hi,
I tried out the light switch example on a nRF52833 and it seems not to be reliable at all. So i connected the debugger and saw, that in access.c,
in packet_alloc_and_tx...
Hi all,
I am trying to use nrf52840 dongle as hci_usb with the very simple task: scan
Host is Raspberry Pi with BlueZ
Controller is nrf52840 dongle with firmware hci_usb...
Hi
I want to move DFU at the application level. Is this possible? I want to move DFU at the application level because of my project requirement.
1. In my project, I have...
Hi, I am trying to get the BLE values on Thingy91 (PCA20035) . And I have followed the
devzone.nordicsemi.com/.../217018 I have ported the diff (nrf and zephyr diffs from...
I am using built-in DTLS for encrypting my UDP traffic. In order to save expensive data quota and reduce battery drain, I have to make use of session resumption, so that I...
Hi. I have a question about Bluetooth 5.1. I just want to know what the main difference is between a Bluetooth 5.0 and Bluetooth 5.1 chip.
Is it the hardware or software...
I am developing a firmware on a nrf52840 board with FreeRTOS. Unfortunately, due to a mistake during the development process, the board misses the XTAL 32,768 Hz.
Is there...
Hi Nordic:
I want to build a raspberry connected to a 52832 board via uart,
this raspberry pi with 52832 board need doing secure DFU to remote BLE device, the raspberryPI...
Using the nRF9160 on the Verizon network we are having some issues with eDRX. Specifically sending data to the device from our MQTT server.
We have configured a eDRX interval...
Hi,
I am working on nrf52 msc example. I am required to use internal flash for msc. In example there is support for ram, sd card and spi flash. I am required to use internal...
Hello,
I'm currently trying to sniff the DH Key Exchange as specified in Spec 5.1 p.2446. I'm using the nRF51 Dongle as sniffer, the nRF52 DK as slave and the nRF52840...
Hi,
I am using two nRF52840 DK in which one of the board is flashed with light switch client and other one is flashed with light server and a nRF mesh app is used for provisioning...
Hi,
I see Nordic has recently released an updated software to do direct test mode (without the use of python or the old nRFGo studio). I am able to run the test code on...
Hello,
I am using nRF52840, SDK_16.0.0, S140 SoftDevice and Segger 4.16 for flashing the image.
1) While upgrading over serial interface using DFU, whether UART needs...
