Hi,
We are using the ble_app_uart example in evaluation board to read data from some sensors and send it to the nRF UART V2.0 in Android 4.4. Every 20 ms I am trying to...
I am try this at nrf51_sdk_v6_0_0_43681\nrf51822\Board\nrf6310\s110\ble_app_hids_keyboard
Firt I connect to Android device and keep one whitelist.pp_addrs and one whitelist...
Hi,
Parameter uint8_t ble_gap_scan_params_t::filter is present in the documentation, but not implemented.
Checked for SDK 5.2.0 and 6.0.0.
devzone.nordicsemi.com...
After I get a Disconnected() event, I want to start scanning again, therefore try to call StartDeviceDiscovery() again.
IsDeviceDiscoveryOngoing was checked before.
The...
Hi, I wanted to ask a question regarding sending data.
I currently have external memory that will send out serial data (SPI) to the nordic microcontroller. I have saved...
Recently, I try to programme nRF51822 DK communicating with nRF2401e1 DK,unfortunately，which does not success. With setting radio configuration: TXPower,frequency channel...
E:\BLE\work\nrf51_sdk_v6_0_0_43681\nrf51822\Board\nrf6310\s110\ble_app_hids_keyboard
SDK 6.0.0
Softdevice 7.0
When I connect to Android 4.4.3 device(Nexus7 II) will...
I am trying to flash TCP-Server example from IOT SDK from Eclipse.
Project builds without errors.
But I am getting this warning message in Eclipse console when I flash to...
s130, nRF5_SDK_12.1.0_0d23e2a, SoftDevice 8_9_0.
I want to use the Central Glucose Service, how do i modify the "ble_central/ble_app_hrs_c" example code?
int main(void...
I wanted to use MQTT example with nrf52 DK board.
and I uploaded MQTT firmware which is located MQTT example folder in iot SDK.
www.youtube.com/watch
I tried to follow...
Hi,
I want to implement handler for undefined instruction fault. According to Cortex M4 documentation (ARM DUI 0553A subchapter 2.3.2 "Exception types") this fault leads...
Hi everyone,
I've been experimenting compiling my project with Clang and have run into some issues with the supervisor calls and their wrapper in nrf_svc.h.
Without...
Hi,
I want to implement simple module:
gpiote event on pin change (around 6.7MHz signal)
Route gpiote event through PPI to increment counter
Toggle GPIO pin...
According to the documentation, the function sd_ble_gatts_exchange_mtu_reply() can return NRF_ERROR_BUSY , which would require the application to somehow defer the call to...
Hi,
I am attempting to run the examples of BLE HRS C and BLE HRS Peripherals from the SDK. Getting to the connected state works (discovery and notifications as well) just...
I noticed that the ram setting in this example is from 0x20003440, this means only less than 1KB is for application. But the example in sdk 12.1 the ram is from 20002078....
We want to use IoT SDK where two or more nRF52 chips would talk to each other via 6lowpan, in that case is the ble enabled router necessary for such communication?
I have an nrf51822AC chip connected to another ARM based processor which provides a CAN interface. The two are connected via the UART and we are using the ble_connectivity...
Hi, in the current project I'm working on, I need to develop an Eddystone beacon with UID and TLM frames configured by default. Based on the experimental_eddystone example...
Hi, Nordic
I need write some information to flash, then power off and power on, nRF52 still can read previous information. But now, nRF52 can not read, maybe ESB is still...
