I will be deploying my nRF51822-powered devices into the field and the end user will not be able to have any physical access to, for example, power cycle the board. I need...
Hi,
We are using the ble_app_uart example in evaluation board to read data from some sensors and send it to the nRF UART V2.0 in Android 4.4. Every 20 ms I am trying to...
I am try this at nrf51_sdk_v6_0_0_43681\nrf51822\Board\nrf6310\s110\ble_app_hids_keyboard
Firt I connect to Android device and keep one whitelist.pp_addrs and one whitelist...
Hi,
Parameter uint8_t ble_gap_scan_params_t::filter is present in the documentation, but not implemented.
Checked for SDK 5.2.0 and 6.0.0.
devzone.nordicsemi.com...
After I get a Disconnected() event, I want to start scanning again, therefore try to call StartDeviceDiscovery() again.
IsDeviceDiscoveryOngoing was checked before.
The...
Hi, I wanted to ask a question regarding sending data.
I currently have external memory that will send out serial data (SPI) to the nordic microcontroller. I have saved...
Recently, I try to programme nRF51822 DK communicating with nRF2401e1 DK,unfortunately，which does not success. With setting radio configuration: TXPower,frequency channel...
I have been working on a project that involves two nrf51 dev boards, one is acting as a central and the other is acting as a peripheral, and I have been encountering a problem...
Hello!
For beginning with nRF51 I chose BLE Nano set of boards (BLE Nano + MK20 USB donbgle) and it was of great help to easily begin with BLE.
So far, we came to the need...
As an experiment, we want to implement soft power off for nRF52 with external components. We want to keep the entire circuitry entirely switched off, and after a press of...
I do not use board.h nor bsp* in my project, and also I am not initializing the pins that I do not use in my program currently - so P0.17 is not initialized and setup. However...
Hi all,
I am new to nrf51-dk and I am using nRF5 SDK v11.0.0.
I wanted to perform the task below.
When the DK is turned ON, read on board push button status.
If button...
We are implementing scan functionality in nRF51. I would like to understand if anyone has tested or tried to scale this functionality when there are thousands of beacons around...
Hi everyone,
I was wondering how GAP calls and events are synchronized within the SoftDevice.
Example:
// conn_handle is updated in the CONNECTED and DISCONNECTED...
The Android Master Control Panel app has an option to remove bond information (which works). But the API for it is hidden .
I'm just wondering if you use reflection to...
We are trying to replace an existing solution that uses a custom Service with 4 Characteristics. Unfortunately none of those share the same base UUID.
Basically the Service...
Ok - I'm trying to get my arms around this bootloader process.
I am using the nRF5_SDK_11.0.0_89a8197 SDK along with the PCA10040 develeopment kit.
I also am using IAR...
I'm trying the run the smart remote 3 v1.1 firmware built using IAR.
The firmware fails to init the touchpad and enters a forever loop.
The program only builds with optimization...
Hi,
I am using nRF52832 with S132_V2.0.0 and SDK_11.0.0. In my application i plan to use RFX2411N PA/LNA module. In datasheet of RFX2411N, I found that it can be used in...
Trying to qualify our design with Bluetooth SIG.
NRF51422 QFN48 nRF51 SDK v10.0.0 SD 310
When I use QDID 62791 to generate a test suite for PTS on the SIG website, the...
Hi,
I have a code programming the nRF51422 development board to write to a Sharp Memory 96x96 pixel LCD screen using SPI.
Currently the code writes two numbers and a...
