Hi,
I use UART bootloader SDK example(dfu_dual_bank_hci) to do update firmware on EK PCA10001 board,it can work ok.But i changed the HCI_SLIP_UART_RX_PIN_NUMBER and HCI_SLIP_UART_TX_PIN_NUMBER...
Hi. I have been trying get a notification through ANCS.
I have created an app which is made by modifying ble_app_ancs sample.
It works basically but there is one problem...
Hello,
I'm using the nrf51422 with 210 softdevice.
I'm trying to figure out a way for the receiving slave device to go to sleep when away from the master, but to wake...
To be able to upgrade FW through UART, a bootloader for nrf51822 is required in my project. I have tried out the example bootloader in SDK. But this example is using softdevice...
I followed the forum posts and nan-29 to get eclipse 4.3.2 to successfully connect to JLinkGDBServer via a Segger J-Link EDU on Ubuntu Linux.
I can start the GDB server...
I'm using Softedevice 6.0.0 and SDK 5.2. and Keil 4.7.
I Modified bootloader project so it compiles with both ble and hci transports. Currently I use button_0 and button_1...
I am working on the proj that needed 2 MCU and nrf51822 work as slave.
I would like to know any ref on how to firmware upgrade on board without external tool?
Good health to all! I am using Ble, I need to flash received packets. The best way to do this is using sd_flash_write (). In the sdk_config.h file, I see #define NRF_FSTORAGE_SD_MAX_WRITE_SIZE...
Hi,
I tried importing existing project (In IAR) to Segger embedded studio, And getting following error.
When code is built, Ses compiling the files but giving...
Hi all, I've just started moving to the nrf52840 platform from another ble module. I'm taking samples from a bunch of sensors at about 20 hz, since this is a battery powered...
Hi Dev Team,
I am using the mqtt_simple example to publish my data out every 1 hour. I tried the example and it is working well and I was able to test it via MQTT.fx with...
Hi,
Is it somehow possible to plot data comming from external target board with nRF52, connected to nRF52 DK via swdio and swclk lines, by some data plotting program? Etc...
I am using NRF52832 for BLE application with softdevice 132 under SDK15.3. My application is supposed to sleep off after certain amount of time when there is no user activity...
I am using two SAADC channel on nRF52 DK, one for pressure sensor and another for battery level. I realized 0.5mA is higher than single channel. Is it normal?
We need to develop a portable device，In order to save cost and low power consumption.We need to know how to make nrf52832 connect to the Internet through the Bluetooth network...
I wrote a program to toggle the pins of P0 and P1.
When I write:
P0=0xff;
P1=0x00;
Only P0.0 - P0.3 are high and P0.4 - P0.7 and P1.0 - P1.6 are low.
P0=0x00;
...
Hello,
I am talking about nRF5_SDK_17.0.2_d674dde/components/libraries/log/src/nrf_log_frontend.c.
In the case of HEXDUMP there seems to be some inconsistency in the packet...
Just downloaded this (5.10d) on MacOS 10.15.7.
(Planning to test with 9160 DK.)
Using getting started assistant
Got as far as the "setup a project in SES" (installed...
This is our 4th nRF52840 DK this year that got damaged this way. After using it for 1 to 2 months the DK does not work power up normally. Then we can only use the board with...
In RADIO - 2.4 GHz radio TXPOWER register say:
"When the radio is operated on 1.2V, the output power is increased by 3 dBm, i.e. if the value -20 is specified, the output...
