I am working on the proj that needed 2 MCU and nrf51822 work as slave.
I would like to know any ref on how to firmware upgrade on board without external tool?
We're looking for a Nordic nRF51822 based low profile/small USB dongle that we can use for our iBeacon software.
It would need to come complete with casing and the ability...
Hi all,
i want to establish connection between two threads in cmsis-rtos, can i use
1) semaphore to do this?
2)message queue should be used or any other ipcs can be...
Hi,
I have two CPU in our product. (STM32F2 and Nordic nrf51422).
I use serialization function to link those two CPU(refer to ble_s110_serialization sample)
But I find...
Hi,
My behavior is as follows
Turn on my device(use 51422) and advertising(2 Service and 3 Characteristic)
Turn on my cell phone(Samsung Note3),scan my device...
Hello:
I used analog IIC write MPU6050. Again after power download programs, mpu6050 can run up there ACK response. But the debug will not run. Simulation IIC because no...
Hello!
How can I communicate with my nRF24L01+ and nRF51822 at the same time. I can set up same channel, CRC-mode and I don't use ESB. But what about address? How do I set...
Hi,The Nordic team
My product is developed based on Nrf54L15. Now I want to conduct the inheritance certification for Thread. Ho w should I fill in the following information...
Hello,
I've seen some posts mentioning a problem with the UART missing bytes on the RX, potentially at higher baudrates. I'm communicating with a module that uses a 921600...
I have developed an nRF52840 board that implements the following basic logic:
Onboarding Zigbee Devices : Supports Zigbee devices joining the network.
Creating Device...
Hello Nordic Team,
I am currently working on the development and certification testing firmware for our product that uses the nRF9160 as the main host MCU. BLE is provided...
i use two development boart, one download "channel_sounding_ras_initiator" example, the other download "channel_sounding_ras_reflector" use two board to test distance, the...
I’m currently working on a setup with two Initiators and one Reflector using the Channel Sounding sample. My goal is to get distance measurements either simultaneously or...
Hello Nordic Team,
We are working on a cellular IoT application using the nRF9151 and nRF Connect SDK v2.9.0 . Our goal is to connect to AWS IoT Core using MQTT over TLS...
Hardware: nRF9151DK OS: Windows 11 Toolchain: nRF Connect SDK v3.1.99 (Toolchain v3.1.1) Debugger: Onboard J-Link (Interface MCU)
Description of the Issue: I am facing a...
Hi all,
I’m developing firmware using USB CDC with UART async API to transmit data at about 102 kB/s . However, during uart_tx() calls, I often get a -16 error (EBUSY)....
I am using the nRF54L15 with SDK 3.0.0 and developing using npm2100_fuel_gauge for the nPM2100.
I see the battery model for the CR series only includes CR2032, but I...
Hi there.
I am currently working on WIFI provisioning using BLE using nRF7002 and nRF5340.
The CPU structure of my custom board is based on the nRF7002DK. So I am testing...
Hello,
My first attempt with channel sounding.
Hardware Setup:
- Initiator: nRF54L15 DK running `channel_sounding_ras_initiator` sample (no issues found so far) - Reflector...
nRF9160, mfw 1.3.7, NCS 2.9.2
Case:
The modem first connects to LTE-M (Germany, band 3), pretty well.
Then the modem is moved into a building basement (band 8 or 20...
Hi Team,
We are using nRF54L15.
1. Is there any api to read BLE MAC address?. If yes, can please provide it?
2. What are the configurations need to make 'yes' in ...
