Hi all,
i want to establish connection between two threads in cmsis-rtos, can i use
1) semaphore to do this?
2)message queue should be used or any other ipcs can be...
Hi,
I have two CPU in our product. (STM32F2 and Nordic nrf51422).
I use serialization function to link those two CPU(refer to ble_s110_serialization sample)
But I find...
Hi,
My behavior is as follows
Turn on my device(use 51422) and advertising(2 Service and 3 Characteristic)
Turn on my cell phone(Samsung Note3),scan my device...
Hello:
I used analog IIC write MPU6050. Again after power download programs, mpu6050 can run up there ACK response. But the debug will not run. Simulation IIC because no...
Hello!
How can I communicate with my nRF24L01+ and nRF51822 at the same time. I can set up same channel, CRC-mode and I don't use ESB. But what about address? How do I set...
Hi all,
i want to know answer related to following question
1)what is use of uicr?
2)if i place some value in uicr and then change the image,then is there will be change...
It used to work, but now it says "Connected" but the rest of the GUI never changes and the mouse just shows a busy spinner. Here's the log file:
0;13:45:18.9900 [MainThread...
Hi,
My project is based on SDK15.3 with NRF52840. I have referred to the "writable_ndef_msg" example to read/write the emulated NFC tag successfully. And I can get back...
Hai ,
In my application i should connect parallel connection and peripheral and central part connections simultaneously.
for this i developed from hrs_relay example .in...
Hello,
I'm trying to program a nRF52840 Dongle with the thread MTD client example by using nRF Connect but I get an error saying I need to add a SoftDevice. I thought...
Hello, I am new to NRF52. I have setup a project under Embitz ide. I can compile GPIO toggle code and program the the code. However when I try an transmit example github.com...
I have 100 samples of string data (Ex: AABBCCDDEEFF:1592636399:1592636399 ) . I am using the flash_fds module. Also, I want to read the read all the samples at once. I am...
Hi,
I am developing the 'buttonless dfu' to the 'hrs freertos' using the SDK v15.3.0.
However, after I compiled the modified code and loaded to the target broad, I got...
Hi
In ble_stack_init(), err_code = softdevice_enable(&ble_enable_params); err_code = sd_ble_enable(p_ble_enable_params, &app_ram_base); err_code is 4.
I use nrf51822 in...
Hi,
I got a nrf5340 pdk, and I download demo Peripheral_Heart_Rate into board, load peripheral_hr.hex into app_core and load hci_open_amp.hex into net_core. it running ok...
Hello. I have one multirole device (device A) and three peripherals (devices B, C, D). Device A connects to devices B, C, and D as a central role, and connects to the phone...
Hi,
I am developing a product using nRF52833 . (S113, SDK 16, IAR8)
I am developing based on the usbd_ble_uart sample.
I use ble, spi, twi, ppi, saadc.
and, I use...
Hi,
On page 420 of the nRF52811 datasheet (v1.0) it states that pin 14 (P0.18) can be either 1) Digital I/O or 2) Single wire output (SWO). The SWO is not mentioned on any...
Hello, In our project the nRF52 resets randomly
we use the NRF52832 with softdevice S332. On the application space we run a FreeRTOS application with 2 tasks. We want to...
Hi,
I am trying to determine whether or not to use a watchdog timer in our firmware. The device is and IoT device, making sensor readings and entering sleep mode for a while...
Hi all,
i am trying to merge ble_app_peripheral example with twi_scanner. So i created twi_ad7147.h and twi_ad7147.c with the twi configurations.
But i am getting this...
