Hi,
I have two CPU in our product. (STM32F2 and Nordic nrf51422).
I use serialization function to link those two CPU(refer to ble_s110_serialization sample)
But I find...
Hi,
My behavior is as follows
Turn on my device(use 51422) and advertising(2 Service and 3 Characteristic)
Turn on my cell phone(Samsung Note3),scan my device...
Hello:
I used analog IIC write MPU6050. Again after power download programs, mpu6050 can run up there ACK response. But the debug will not run. Simulation IIC because no...
Hello!
How can I communicate with my nRF24L01+ and nRF51822 at the same time. I can set up same channel, CRC-mode and I don't use ESB. But what about address? How do I set...
Hi all,
i want to know answer related to following question
1)what is use of uicr?
2)if i place some value in uicr and then change the image,then is there will be change...
It used to work, but now it says "Connected" but the rest of the GUI never changes and the mouse just shows a busy spinner. Here's the log file:
0;13:45:18.9900 [MainThread...
Hi all!
My question is:
My own application is built based on the example "ble_app_template", and according to the nrf51 SDK - Examples - BLE Peripheral, this example...
Hi!
I'm trying to transfer data from UART to BLE in NRF52810. NRF52810 connects MSP430 controller via UART, MSP430 sends packet of 16 bytes lenght every 2ms (500 times in...
Hi,
I've seen this issue in other threads, but apparently all of them were solved on a private message basis.
So basically - my application for SUPL-C license keeps getting...
I am encountering an issue with PERSISTENT_STORAGE enabled. Currently I have a device set up to rapidly send out messages to test the sequence number updating and block allocation...
Hi Team,
We are using nrf9160 DK and we are new to begin this, We updated modem firmware using programmer, Now we would like to test the modem firmware.
So here are...
Hello,
This is first time to design the PCB antenna for nRF52840 BLE Chip. Can i use the nRF52840 DK Board HW layout for reference or should i use the USB dongle for nRF52840...
SDK16
S132
nrf52832
SES / Windows 10
After much searching this site and the web in general I'm reaching out for support.
While in low-power mode I'm seeing a pulse...
Hello im an Android developer and we have an app that uses an older library but still works with are older products.
we currently use
implementation 'no.nordicsemi.android...
From what I read on DevZone it seems that there is a limitation in nrfutil when needed to update BL+SD+APP. NRFConnect over BLE manages the 2 separate downloads (BL+SD and...
Hello there The problem I encountered was that when getting the slave service, returning to get the service failed. I used DEBUG to check the p_ble_gattc_evt->gatt_status...
Hi,
I am using nrf Connect SDK v1.2.0 in Segger Embedded Studio 4.52 and developing on a nrf52840 development kit (pca_10056). I use the "configure nrf connect sdk project...
My goal is to establish a BLE connection between the DK and the smartphone, using NFC for the OOB pairing . I am using the nRF52 DK and the nRF5 SDK , v.16.0.0.
The intended...
Hi,
I am having issues with getting SPI up and running on my nrf52840-DK using NCS. I've tried getting support about this in another ticket but it seems like it lead to...
Hi,
We are using the nRF52840 SoC.
The following image is taken from the datasheet:
It shows a Gain block before the SAR core
a. Does the Gain block serve also...
Hi ,
I want to know if it is possible to close/open the uart connection with RTS and CTS pin in order to have a low power UART?
When RTS and CTS are high, uart is closed...
Hi,
Can any Zigbee application receive ieee radio interrupts in both TX and RX path?
What I need is:
In the case of Zigbee Tx, an advance notification of 200 μs would...
