Hello,
I'm using the nrf51422 with 210 softdevice.
I'm trying to figure out a way for the receiving slave device to go to sleep when away from the master, but to wake...
To be able to upgrade FW through UART, a bootloader for nrf51822 is required in my project. I have tried out the example bootloader in SDK. But this example is using softdevice...
I followed the forum posts and nan-29 to get eclipse 4.3.2 to successfully connect to JLinkGDBServer via a Segger J-Link EDU on Ubuntu Linux.
I can start the GDB server...
I'm using Softedevice 6.0.0 and SDK 5.2. and Keil 4.7.
I Modified bootloader project so it compiles with both ble and hci transports. Currently I use button_0 and button_1...
I am working on the proj that needed 2 MCU and nrf51822 work as slave.
I would like to know any ref on how to firmware upgrade on board without external tool?
We're looking for a Nordic nRF51822 based low profile/small USB dongle that we can use for our iBeacon software.
It would need to come complete with casing and the ability...
Hi all,
i want to establish connection between two threads in cmsis-rtos, can i use
1) semaphore to do this?
2)message queue should be used or any other ipcs can be...
Recently,I confronted some particular circumstance that I have never came across.
The device programmed used by Jlink and Keil,so I check the address of flash,it showed as...
hi all,
i'm using nrf905 for wireless communication at range of about 30meter @433mhz.
and have some question ,maybe your guys can help me.
thank you.
q1:upclk pin...
According to the documentation, it is possible to upgrade the Thingy:52 firmware via a cable connection using nRFgo Studio. Can I connect the Thingy:52 directly to my PC?...
Dear Nordic Team,
Thanks for supporting.
Now i am trying to work DFU with NUS example.I am following As per nordic document like: infocenter.nordicsemi.com/index.jsp...
I am trying to communicate with DS1307 (RTC) using TWI on nRF51822.
I have configured the pins, address (0x68 fixed for DS1307), frequency and enabled TWI.
Now I am about...
Dear Nordic,
Some time ago we started a project in which we decided to use ANT protocol to communicate wirelessly. However, now that we are going to production in a very...
my programer have many place use sd_ble_gatts_hvx() send data , if i get the BLE_GATTS_EVT_HVC ,how i know this return value return belong which use sd_ble_gatts_hvx(),how...
how to save a problem,if one Thread use sd_ble_gatts_hvx() send many package ,but i use vTaskDelay(50)( the freertos delay api ) when one package send ,then send another package...
SDK： nRF5_SDK_11.0.0
Softdevice： s132_nrf52_2.0.0_softdevice
I read an article about the connection, pairing, bonding and whitelist, there are some doubts：
Bonding...
i want to send data according the ruture value , because we all the data send ruturn value ble_evt_tx_complete ,how i can distinguish difference channel'return value
I've been trying to trying to upgrade some code from SDK 12.1 to 12.3 and it no longer fits in 16k RAM.
I initially thought the problem was this data segment in the linker...
Hi,
I recently started working with the NRF51DK,I need to read data from KX022 accelerometer via I2C and transmit the results over BLE.
I am using TWI_SENSOR example...
when i send many package from programer different place , the return ble_evt_tx_complete have many times. how i distinguish which the ble_evt_tx_complete reture is that place...
