Hello,
I have set nRF51822 Evaluation Kit. With its help, I would like to read the pulse of the heart rate monitor:
link text
I manage to connect to it using the...
Does the s110 stack allow retrying pairing procedure?
It looks like the stack (peripheral) always ends with disconnect upon invalid passkey.
We would like to explore the...
Hi Guys,
since yesterday i am trying to get the DFU with Softdevice S110 (BLE) v7-alpha3 working but haven't succeeded yet. My process is the following:
s110_nrf51822_7...
Hi All,
i would like to know about
1) what is channel in nrf51288?
2) is there any mathematical relationship between channel no and pin no as in ble_app_hrs
example channel...
Hi,
I use UART bootloader SDK example(dfu_dual_bank_hci) to do update firmware on EK PCA10001 board,it can work ok.But i changed the HCI_SLIP_UART_RX_PIN_NUMBER and HCI_SLIP_UART_TX_PIN_NUMBER...
Hi. I have been trying get a notification through ANCS.
I have created an app which is made by modifying ble_app_ancs sample.
It works basically but there is one problem...
I'm trying to change the mac address of my nRF51822 chip using something like:
ble_gap_addr_t m_address_1;
m_address_1.addr_type = BLE_GAP_ADDR_TYPE_RANDOM_PRIVATE_NON_RESOLVABLE;...
Hi,
I use GCC for compilation and nrfjprog for flashing. A few weeks ago I needed to switch on compiler optimization (Level 1) because my code grew a little too big. Now...
Hi,
I would like to have several nRF51 development cards connected to my computer at the same time using the USB debug port. The serial port and the RTT port work when several...
Hi,
We are trying to develop application with OTA DFU on nRF51. And we need to build bootloader ourselves. We use gcc for development. We found the bootloader example for...
I tried to run beacon example (from SDK 9.0). Even after uploading hex file I was not able to "see" becon. I'm using st-link v2 and openocd. Let me tell a bit more about what...
Hi,
I'm making device with nrf51822 chip and 400mA battery.
It connects to smart phone.
It has to calculate heart rate and some other things, so it's doing it on device...
Hi All,
I just bought the Nordic Semi nRF51822 DK (without the starter kit). I tested the Heat rate monitor app and it worked fine. It could send some random values to...
Dear all,
I tried the example program ble_app_uart given in the examples section of the Nordic folder in Keil installation. I created the hex code and programmed my chip...
I was just at the Nordic nRF52 Global Tour in Atlanta and I received the nRF52 Development Kit (PCA10040). One of the Nordic engineers mentioned that the nRF52832 is at rev...
Hi all,
I am using the BLE nRF8001 and EFM32 (ARM Cortex M3). I used the following SDK for connecting the modules using ACI (SPI). github.com/.../ble-sdk-efm32
Now I...
brownout reset = 1.7V
Operating conditions VDD(Supply voltage,internal LDO setup) = 1.8V
(by 1822 Product Specification)
In between 1.7V of 1.8V, or it would have been...
Greetings, I've been using the ARM GCC tools for about 2 months with success for programming the NRF51 DK board. Now I would like to try out the example found in:
examples...
I run step by step the example of adding DFU to ble_hrs, everithing runs fine.
I try to change in the same way another example, ble_app_proximity.
The problem is that...
Hello everyone
i have created one custom service and i succed to compiled then i checked my service via master control panel it is showing unknown service but i named it...
