Dear Nordic Experts, This one's a tough nut to crack:
The firmware is based on nRF5 SDK for Mesh 5.0.0 with nRF5 SDK 17.0.2 and Softdevice s132 7.3.0. It runs on a nRF52832...
SoC: nRF5340 SDK: nRF Connect SDK 1.9.1
CMAC calculation works fine with SDK 1.7 and SDK 1.8. But it failed with SDK 1.9.1.
psa_mac_sign_setup returns error = PSA_ERROR_NOT_PERMITTED...
Hi, I'm pretty new to microcontroller programming so please correct my wrongs.
I'm using the Libuarte driver library to have the pca10040 talk to my server via serial connection...
Hello,
Fllow the guide of Configuring and performing DFU over Mesh,I can update firmwre successful use DFU:
Source: Example/Dfu
Target: Blinky(about 180 segment)
But...
Hi, I am working on custom board with nrf9160. I want to use LTE LINK MONITOR but my uart don't work. I create simple helloworld application from samples. I change uart0 rx...
Hi, We've been having problems trying to implement a high-speed uart communication between the nRF52832 and an STM32. We switched to using libuarte so we can use DMA even...
I'm running the Nordic/Thread SDK 3.2 with an NRF52840 (Rigado BMD-340) on SES 4.42.
I've got a project using BLE + Thread and I'm having problems implementing a hardware...
A multiperipheral connection to a central, all with custom nordic devices (nRF52840) has been stablished. Comunication and connection work just fine, but after a synchronization...
Hi ! I am represnting company responsible for fruitymesh ( https://github.com/mwaylabs/fruitymesh ) which is an open-source proprietary ble mesh running on nrf5 chips. For...
Dear Support,
I have adjusted the radio test example in SDK16.0 for my custom hardware application using the nRF52840. I have followed the instructions on this page to...
To the kind attention of Nordic support team,
As it was said https://devzone.nordicsemi.com/f/nordic-q-a/57531/sdk16-nrf52810-secured-gazell-keil
the secured gzll library...
Hello,
I'm able to program the code (below) to the nRF52 DK. Leds 17 & 18 are working.
I'm unable to program the code to my custom board. Leds 9 & 10 are not working ...
Is there any problem with beacon advertisment and ADC? I have 3 adc pins configured to measure three different sensors... When i use UART over BLE... everything is ok.. but...
Hi!
I seen video and read manual how to use it, but still not doesn't work.
PPK + PCA10040
on the PPK board I set jumprs to DK (all 3 pcs). USB connected to PCA10040...
Looking through the datasheet, current consumption is provided for the nRF9160 Modem at 3.0V and 3.5V. Is it possible to get information on 5V related current draws? I've...
Hi,
I am using the example nrf5-ble-mpu-simple from nrf5-mpu-examples-master to do the following:
a) send a BLE beacon advertisement (non connectable)
b) periodically...
We are currently having an issue with DFU failing on Samsung A7 a running andorid 6.0.1. We are using nRF Toolbox for BLE (DFU application) and when I try to connect the device...
Good day!
I'm working on Time model fro Bluetooth specification.
Question is about time handler. I can't figure out should I write a separate handler for TAI, or I should...
Hi!
I´m currently using the nRF52840 demo board to determine the bluetooth range of the device I'm working on.
The question is: which is the orientation of the antenna...
