Dear Sir
We got the problem on DFU upload firmware, it always failed in second DFU . We must unpair the device at iOS setting panel. Before next DFU.
Here is the log data...
Hi All,
My requirement is to read the data from nRF51822 device that is connected to a bluetooth and bluetooth is connected to a system using a .Net application.
I have...
Hi everyone,
I'm using the nRF51822 (pca10000 Dongle + pca10005).
My plan is to send one byte over the radio.
I tried to use the SDK-Example as a template but it's...
Hi,
Is that possible to run the radio_test_example (\nRF51 SDK_v5.2.0.39364\Nordic\nrf51822\Board\nrf6310\radio_test_example) on the nRF51822EK? If yes, what modifications...
we also produced self PWM for ADC wave form testing. when we stop transmission, we will get good waveform out, but when we starting transmission, output waveform shape is...
Dear Support,
I have some troubles with the Evaluation Kit for nRF51822 :
I use the broad as a central role with S120_nrf51822_1.0.0_softdevice.hex and example...
Suppose a nRF9E5 transmitter is set for continuous transmission on a channel.
A nRF9E5 receiver listening on that channel:
finds carrier and sets CD
finds address...
I have a BMD-340 eval kit (uses nRF52840) as does my contracted developer who has sent me a hex file to program into my board. I have installed The Segger Embedded Studio...
My configuration:
IAR V8.22
Custom board with nRF52832
Softdevice V6.0.0
SDK 15
I understand that BLE uses, in the link layer, CRC to verify packet integrity...
Hi, has anyone interfaced with the SX1272 using the nRF52840? Perhaps they could point at us some LoRa SDK or libraries which will help the development process?
Thanks
Would a wire-wound inductor work better than a chip inductor for the antenna circuit of NRF52810? I'm using the 32 pin QFN package with the LDO configuration which calls for...
I need to calculate the max number of concurrent connection Central can support given the following
Connection Internval = 7.5ms
Baud Rate per connected peripheral:...
Where can I find this version of hub?
ERROR: Could not find a version that satisfies the requirement hub==2.0 (from -r zephyr/scripts/requirements.txt (line 10)) (from versions...
When nrfutil is installed with python 3, I get an error when generating bootloader settings page. This does not occur with python 2. As python 2 support expires very soon...
Hi.
I am testing MESH by nrf5SDKforMeshv201src and nRF5_SDK_15.0.0_a53641a.
I have a problem.
My project have one of the client and one of the server.
Client transmit...
Hi I had a question to setup the MCP2515 driver in the zephyr project.
We have a custom board for the decawave DWM1001 module, which uses a nRF52832 chip. They have a device...
Hello I am using a I2C sensor module and I need to tranmit only address to receive data back, but I dont know how.
Program crashes on line 4.
Thank you for your help...
I have a DK52 with another device at attached to the SPI bus. I also have a PPK. Should
I connect the second device to VDD_nrf to count as a load? right now it is connected...
When the bluetooth service function is initialized, sd_ble_uuid_vs_add() is called in the ble_dfu_buttonless_init() function in case of an out of memory error. In the ble_nus_init...
Hello, Is there any evaluation kit available for NRF905? I found this one online but DIGIKEY website says its obsolete::
media.digikey.com/.../nRF905-EVKIT_PS_Rev1.0_Jan2004...
Dear Nordic staff and users,
Now I'm trying to confirm that my local LTE operator supports energy saving modes. It went with flying colours with PSM:
at+cereg=5 OK at...
