Hello,
I have set nRF51822 Evaluation Kit. With its help, I would like to read the pulse of the heart rate monitor:
link text
I manage to connect to it using the...
Does the s110 stack allow retrying pairing procedure?
It looks like the stack (peripheral) always ends with disconnect upon invalid passkey.
We would like to explore the...
Hi Guys,
since yesterday i am trying to get the DFU with Softdevice S110 (BLE) v7-alpha3 working but haven't succeeded yet. My process is the following:
s110_nrf51822_7...
Hi All,
i would like to know about
1) what is channel in nrf51288?
2) is there any mathematical relationship between channel no and pin no as in ble_app_hrs
example channel...
Hi,
I use UART bootloader SDK example(dfu_dual_bank_hci) to do update firmware on EK PCA10001 board,it can work ok.But i changed the HCI_SLIP_UART_RX_PIN_NUMBER and HCI_SLIP_UART_TX_PIN_NUMBER...
Hi. I have been trying get a notification through ANCS.
I have created an app which is made by modifying ble_app_ancs sample.
It works basically but there is one problem...
Hi,
I am struggling with a low power consumption solution for waking the NRF52832 with our product which is using a third part module.
Currently our product total power...
Hi, I have Lenovo tab E8 tablet with Android 7.0 and I connect to a BLE device (nrf52832 SDK 15.2.0 S132) from my Qt 5.11.2 app. After succesfull connection I discover services...
The toolchain setup of the NRF91 is extremely complicated. Is the a VM Image or Docker container that has everything pre-configured? I am trying to setup up a linux VM now...
I have a 52840-DK (PCA10056) connected over USB on Windows 10. I am using IAR and can build and run demos from EW in this configuration but am having no success with nrfConnect...
I am working on a project on the nrf52832 board using mesh SDK v3.2.0 and SDK v15.3. I am trying to troubleshoot an issue with the publish process for BLE mesh, but I am not...
Testing DFU with IOS version of nRF connect. I am able to save my image to the IPad with Itunes. I can select the file and then start the DFU process.
Process completes...
I am trying to setup a VM (Ubuntu 19.04) that has the complete setup for NRF91 development. I have been following the instructions in the nrfConnect 3.2.0 - getting Started...
Dear Support,
In our new project, we have 8 signal LED diodes attached to nrf52832, they are all sinking current:
3x GREEN 0.8mA (P0.16, P0.17, P0.18)
1x RED 3.3mA...
I am trying to setup a VM (Ubuntu 19.04) that has the complete setup for NRF91 development. I have been following the instructions in the nrfConnect 3.2.0 - getting Started...
Hi,
I'm using SDK 15.2. I flashed the dtm firmware on the BLE chip. How can I test its working before sending it to the certifier? I have nrfgo studio & I'm able to start...
Hi Team
We are able to flash nRF52840 based LE Module using nRF52840 DK successfully.
But we would like to know if nRF52 DK also can be used to flash/program this nRF52840...
Hello,
SDK:15.3
If not pair with moblic phone, spi is normal
And obile phone pair 52811 to send data, that also normal
But I want to integrate, then 52811 is NRF_BREAKPOINT_COND...
Hi all:
For SDK15.3, if I want to change 32.768Khz to internal LF clock, Should I enable the CLOCK_CONFIG_LF_CAL_ENABLED of "sdk_config.h" ?
if I disable CLOCK_CONFIG_LF_CAL_ENABLED...
