Hi,
I use UART bootloader SDK example(dfu_dual_bank_hci) to do update firmware on EK PCA10001 board,it can work ok.But i changed the HCI_SLIP_UART_RX_PIN_NUMBER and HCI_SLIP_UART_TX_PIN_NUMBER...
Hi. I have been trying get a notification through ANCS.
I have created an app which is made by modifying ble_app_ancs sample.
It works basically but there is one problem...
Hello,
I'm using the nrf51422 with 210 softdevice.
I'm trying to figure out a way for the receiving slave device to go to sleep when away from the master, but to wake...
To be able to upgrade FW through UART, a bootloader for nrf51822 is required in my project. I have tried out the example bootloader in SDK. But this example is using softdevice...
I followed the forum posts and nan-29 to get eclipse 4.3.2 to successfully connect to JLinkGDBServer via a Segger J-Link EDU on Ubuntu Linux.
I can start the GDB server...
I'm using Softedevice 6.0.0 and SDK 5.2. and Keil 4.7.
I Modified bootloader project so it compiles with both ble and hci transports. Currently I use button_0 and button_1...
I am working on the proj that needed 2 MCU and nrf51822 work as slave.
I would like to know any ref on how to firmware upgrade on board without external tool?
I have moved on to SDK12. But one old project using SDK10 now requires a 128 bit UUID.
I keep getting hard fault when I add UUID.
I noticed that there is no vs_uuid_count...
Hi Team,
I am using nRF5_SDK_11.0.0_freertos_dfu_060516.zip SDK. I have added NUS service with UART configurations in this code successfully.
When I am commented the DFU...
We have both nrf51 and nrf52 running DFU.
How can I identify on the mobile application side whether I'm connecting to nrf51 or nrf52?
They will need to get different firmware...
Hi,
Is it possible to know which type of advertising packet is being advertised by the slave i.e whether it is a connectable or a non connectable advertising packet by...
Hi,
So I have a HEX file with unit specific data that I upload to 0x00062000. This data is about 80kb so it leaves some space incase I need a bootloader in the future....
Hi:
I want to bond and change dev name and storage.
This is my storage dev name init code:
void my_flash_init(void)
{
uint32_t err_code;
pstorage_module_param_t...
Hi all,
i'm using an app_timer.
I need to use three timer for debounce of three button. In my case i have to discriminate the push of three button at same time. When all...
Hello Community
I have read the following threads:
devzone.nordicsemi.com/.../
devzone.nordicsemi.com/.../
In order to know how to discover my services, including...
Hi
Does the CryptoCell in the nRF52840 support secp256k1?
In this documentation it says at one point Koblitz curves using fixed parameters, up to 256 bits, are supported...
I used to do with the iso7816 run on nRF51822 SDK9 and S110_v8.0. However,as the BLE stack is running, the iso7816 interface clock signal is abnormal. as the picture below...
Hello!
I have the board PCA10040 (nRF52 DK).
I designed two different programs:
SPI: I'm using the SPI communication to communicate with an external sensor (accelerometer...
Hello, I am working on a project that involves the implementation of a wireless temperature sensor. so, i bought the DS18b20 digital temp sensor and tried to apply the code...
hello friends:)
i have some problem during making my products,
it's an a interface board with ble that generates UART signal for other board
and i made an schematic with...
Hi,
I noticed weird behaviour on nRF52840 when using LE Coded PHY.
Connection access address is configured as logical address 1 and it works fine when using 1M and 2M...
