Hi,
I use UART bootloader SDK example(dfu_dual_bank_hci) to do update firmware on EK PCA10001 board,it can work ok.But i changed the HCI_SLIP_UART_RX_PIN_NUMBER and HCI_SLIP_UART_TX_PIN_NUMBER...
Hi. I have been trying get a notification through ANCS.
I have created an app which is made by modifying ble_app_ancs sample.
It works basically but there is one problem...
Hello,
I'm using the nrf51422 with 210 softdevice.
I'm trying to figure out a way for the receiving slave device to go to sleep when away from the master, but to wake...
To be able to upgrade FW through UART, a bootloader for nrf51822 is required in my project. I have tried out the example bootloader in SDK. But this example is using softdevice...
I followed the forum posts and nan-29 to get eclipse 4.3.2 to successfully connect to JLinkGDBServer via a Segger J-Link EDU on Ubuntu Linux.
I can start the GDB server...
I'm using Softedevice 6.0.0 and SDK 5.2. and Keil 4.7.
I Modified bootloader project so it compiles with both ble and hci transports. Currently I use button_0 and button_1...
I am working on the proj that needed 2 MCU and nrf51822 work as slave.
I would like to know any ref on how to firmware upgrade on board without external tool?
Hi Guys,
Is there a way with the Keil C Compiler to get an *.LST file or some sort of Assembly output from C source input?
I'm still trying to write some code to drive...
Hi
Now, I am coding SDK5.0.0 keyboard project and almost done. It's Keil C version. Did you have IAR version for reference? Besides, did you know if IAR supports J-Link lite...
Hi,
I just started to interface the lcd display with nrf51822 evaluation board. The display i'm using is, spi compatible, 18" tft (160x130) from tiny lcd. I took spi master...
I would like to know how to implement reset button on nRF51822. Image of schematic would be very useful, but good explanation should be enough. Thank you in advance.
I...
Hello,
I am trying to build the nrf51822/Board/pca10001/s110/ble_app_proximity project, with gcc ...
I have created a makefile based on the button_radio_example makefile...
I would like to know if the Notification/Indication of a Characteristic is enabled. I suppose this data is stored in a CCCD on the stack. I have not found any SVC instruction...
It seems the only way to use the S310 alpha hex on the development kit is to replace the IC on either of these boards; is this correct or is there another way?
Also, the...
Hi,
I am researching BLE product for a similar task (1 central node with 4-6 concurrent slaves). I have looked up other vendors (TI, CSR etc) and come to a conclusion...
After Googling and searching this forum I still don't know if I can make an HID peripheral (a touchpad) for Android that operates over Bluetooth Low Energy, and is accepted...
Over the air downloaded updates are an essential feature for productization. Are there any examples showing how to implement the OAD? Also is it possible to OAD update the...
Hi,
My nRF51822 evaluation board is not working, here i attached the screen shot's of the error messages i used to get on both the nrfgo studio and in keil. Please suggest...
Hi
When I reduce the operating voltage, the nRF51822 with the heart rate demo running resets whenever the voltage drops below 2.1V and does not recover unless I increase...
I need an star network with 1 master and 4 to 8 slaves. I'm not so concerned about the power, but the convenience of the nRF51822 is attractive.
Does the current BLE library...
Dear all:
Now,i have issue ,i can't fund device.(i have sure the hardware is OK)
i think it is program overwrite the J-TAG register(TDO)? but i may not sure.
have any experience...
The Arduino SDK by David Edwin linked to here is no longer available since the Bluetooth forum seems to be down, and has been for some time: devzone.nordicsemi.com/arduino...
