Hi,
My behavior is as follows
Turn on my device(use 51422) and advertising(2 Service and 3 Characteristic)
Turn on my cell phone(Samsung Note3),scan my device...
Hello:
I used analog IIC write MPU6050. Again after power download programs, mpu6050 can run up there ACK response. But the debug will not run. Simulation IIC because no...
Hello!
How can I communicate with my nRF24L01+ and nRF51822 at the same time. I can set up same channel, CRC-mode and I don't use ESB. But what about address? How do I set...
Hi all,
i want to know answer related to following question
1)what is use of uicr?
2)if i place some value in uicr and then change the image,then is there will be change...
It used to work, but now it says "Connected" but the rest of the GUI never changes and the mouse just shows a busy spinner. Here's the log file:
0;13:45:18.9900 [MainThread...
Hi all!
My question is:
My own application is built based on the example "ble_app_template", and according to the nrf51 SDK - Examples - BLE Peripheral, this example...
Hi,
I am using ancs service to get some information of my iphone.
I use nRF51822 microcontroller and Nordic suggests to use the new SDK (5.2) for new microcontroller...
Hello,
I am new to Nordic platform, previously i had worked on TI controller.
I have three questions to ask:
1) My firmware consists of four services, each service...
hi,
I am using nRF52832 with KEIL. I want to use version6.0.0 softdevice, but I can't select from KEIL runtime library.
Also, the version that can be downloaded from...
I am trying to change after 10 seconds into non-connectable mode. I am using the below code for initializing:
I want to change mode into non-connectable using this type...
When I use dfu_nrf52832_xxAA_s132_6.1.1.hex, it works all devices updated with blink code as described in dfu_quick_start.md But without any provisioning Process, why? And...
Firstly , I have 2 phone. Phone A is huwawei using android 7 and Phone B xiaomi pocophone using android 9.
Phone A already success connect using UART. But I want to try...
I have a same question:
https://devzone.nordicsemi.com/f/nordic-q-a/22025/in-nrf52840-not-able-to-program-boot-loader-hex-is-using-nrfgo-studio/86420#86420
But I not working...
Hi, I am trying to run the following demo here: https://github.com/NordicPlayground/nRF52-ble-long-range-demo
I have followed the instructions and copied the demo folders...
In my understanding, only Nordic NRF Connect (Android and iOS) can be used to bootload a device using the Nordic DFU.
Is there a corresponding command line tool to perform...
I followed the issues from https://devzone.nordicsemi.com/f/nordic-q-a/54149/error-by-loading-solution-on-ses, which fixed the zephyr script issues, but was seeing the same...
Hi,
I have migrate to SDK14.2 the MPU9250 exemple from the peripheral folder in the nrf52-pesky exemples : https://github.com/e27182/nRF52832_pesky https://github.com/e27182...
I am using the nRF52840 DK with the s140 softdevice and am trying to copy the interrupt vector table to RAM to modify interrupts during run time.
I run the following function...
I am porting the eMD-6.12 firmware/library by Invensense for the part MPU9250 into the nRF52832. My toolchain is compiling through gcc allowing examples from SDK's to be quickly...
Hi,
We 're currently using an ARM SOM that will run Yocto Linux from NPX for our current project. We have the nrf52840 connect to this SOM via USB, and we want to be able...
I am using SDK V15 with an nRF52DK and Keil compiler.
I have difficulty finding an example to use a GPIO to drive a Piezo Buzzer. The requirement is very simple: use a GPIO...
