Hi,
I use UART bootloader SDK example(dfu_dual_bank_hci) to do update firmware on EK PCA10001 board,it can work ok.But i changed the HCI_SLIP_UART_RX_PIN_NUMBER and HCI_SLIP_UART_TX_PIN_NUMBER...
Hi. I have been trying get a notification through ANCS.
I have created an app which is made by modifying ble_app_ancs sample.
It works basically but there is one problem...
Hello,
I'm using the nrf51422 with 210 softdevice.
I'm trying to figure out a way for the receiving slave device to go to sleep when away from the master, but to wake...
To be able to upgrade FW through UART, a bootloader for nrf51822 is required in my project. I have tried out the example bootloader in SDK. But this example is using softdevice...
I followed the forum posts and nan-29 to get eclipse 4.3.2 to successfully connect to JLinkGDBServer via a Segger J-Link EDU on Ubuntu Linux.
I can start the GDB server...
I'm using Softedevice 6.0.0 and SDK 5.2. and Keil 4.7.
I Modified bootloader project so it compiles with both ble and hci transports. Currently I use button_0 and button_1...
I am working on the proj that needed 2 MCU and nrf51822 work as slave.
I would like to know any ref on how to firmware upgrade on board without external tool?
Target - NRF52832 populated on a custom PCB using SDK 14.0.0 and s132 5.0
Background - end device will be used to send logged IMU data to the cloud via a smart device,...
Hi,
This is my first post here. I hope I will follow the structure of a good question.
I want to have a sequence of defined duty cycles (let's say 4 values). The aim...
serial-rtt.zip I'm having trouble debugging SDK14.1.0 example serial using NRF_LOG with NRF_LOG_BACKEND_RTT_ENABLED using the NRF52 DK, PCA10040.
With NRF_LOG_ENABLED set...
Situation: Trying to upgrade previous versions of the SD and BL (V3.0.0) to (V5.0.0)
Problem: device power cycles after a new application is flashed to the device into the...
I have successfully managed to communicate back and forth ( message ,Temp and Humidity data) between Two Arduino Nano using NRF24L01 module. However when I am trying to receive...
Hello All,
I'm using nRF52810 with SDK 14.1 base on ble_app_uart example. where i am continously receiving the GPS data via UART i changed the uart pin configuration as...
dear nordic employee:
I want to use the PPK measure my hardware
I set as the 《PPK_User_Guide_v1.1》 says,and the led1 is ok
but the ppk cannot work well
the details like...
Hello! Is it possible to subcribe on more then one characteristic (which support NOTIFY) on nRF52832 (in Central role)?
I check it in nRF Connect app, it's working, so probably...
Hi，i use SDK13.1 and nRF52840.I keep the DFU_APP_DATA_RESERVED equal to the FDS_VIRTUAL_PAGES.When i change the pages of them to 200,OTA was broken off when starting DFU.When...
SDK13, S132, nRF52832.
I use whitelist and bond peripherails. But after bonded 20 pcs of peripherials, I can work with only first 8 bonded.
Which parameters should change...
I’m trying to create a nRF8001 device without the need for any keys, because the device will be inaccessible in mounted condition. Additionally the connection must be secured...
I am utilizing the nRF52832 with softdevice S332 with both ANT and BLE enabled (no peer manager). When I set the ANT search for a channel to use ANT_WAVEFORM_FAST it causes...
Hi,
I am trying to use fds file system to save some data in flash,
when using the example code of sdk 14.0.1, it is not normally operated,
NRF_ERROR_INVALID_PARAM error...
Hello
I am using nRF51822 Nordic controller, SDK 9 and S130 Soft-Device.
I have used to generate a 1 KHz PWM signal successfully using timer 1.
And generating a 4 MHz...
Hi,
I have designed one custom board using nrf52810 and GPS module. where i can get the gps data via UART to my nrf52810 chip and then from nrf52810 sending same data to...
