To be able to upgrade FW through UART, a bootloader for nrf51822 is required in my project. I have tried out the example bootloader in SDK. But this example is using softdevice...
I followed the forum posts and nan-29 to get eclipse 4.3.2 to successfully connect to JLinkGDBServer via a Segger J-Link EDU on Ubuntu Linux.
I can start the GDB server...
I'm using Softedevice 6.0.0 and SDK 5.2. and Keil 4.7.
I Modified bootloader project so it compiles with both ble and hci transports. Currently I use button_0 and button_1...
I am working on the proj that needed 2 MCU and nrf51822 work as slave.
I would like to know any ref on how to firmware upgrade on board without external tool?
We're looking for a Nordic nRF51822 based low profile/small USB dongle that we can use for our iBeacon software.
It would need to come complete with casing and the ability...
Hi all,
i want to establish connection between two threads in cmsis-rtos, can i use
1) semaphore to do this?
2)message queue should be used or any other ipcs can be...
Hi,
I have two CPU in our product. (STM32F2 and Nordic nrf51422).
I use serialization function to link those two CPU(refer to ble_s110_serialization sample)
But I find...
I would like to know the files contained in nRF5x_MDK_8_9_0_IAR.msi
as well as other files needed for a minimal application.
I would like to know exactly which are those...
Hello iam using softdevice 110 and SDK 10.0.0, i want to know the way to avoid bonding of device more then once, or deleting the bonding information from persistent memory...
I need to change the flag of the scanrsp. I use the advertising_init() and i try to do like this:
scanrsp.flags = FLAG;
but the function ble_advdata_set(&advdata,&scanrsp...
Hi,
I'm tring to generate private key of dfu, but it didn't work fine.The following is my steps.Did I miss something?
C:\Users\Administrator>cd C:\Program Files\Nordic...
I'm trying to tune a chip antenna for nrf52832. I am not an RF engineer but have figured out how to get the basic VNA measurements done.
I've been fighting with finding caps...
Are there any dirty hacks to pass a little data, like 1 bit even, during pairing?
I need my central to tell the peripheral orientation, left/right, as early as possible....
I am using an nRF52832 PCA10040 board, using s132_nrf52_2.0.0_softdevice.hex, and have AIN0 connected to a potentiometer similar to this . The power input pin is connected...
I am using a eeprep tool which can only be used with command prompt. I am struggling with it.
Here is the format to use eeprep tool :-
usage: eeprep [options] <infile...
Hello,
So — in just trying to get the blink example working, I've come across all kinds of toolchain weirdness. I'm using CrossWorks, because it's on OSX and it's way cheaper...
Hi all
Is possible from softdevice or from program application edit the GAP service? I know this service is mandatory but what about edit the structure which is shown on...
Please give me a professor.
In the nRF 52832 sample project, there is an NRF_LOG_INFO function, is this the ability to output a debug string to the UART?
If so, how can...
I have custom service, where I have declared 2 handles inside BLE Service structure, one for button action and the other for custom battery ADC measurement, each identified...
Hi,
I have seen similar questions to this, but I could not make it work.
I am trying to upload a new code using DFU by means of a smartphone (using nRF Connect) or PC...
Hi. I just noticed this bombshell in the release notes for v13.0.0-1.alpha:
Dropped support for nRF51 Series devices.
Although this is preceded by:
...
Hello ! I am trying to implement a write request but for unknown reason it doesn't transmit back the gatt_status. I have setup the wr_auth = 1. GPIO number 19 si actually...
