Hi Team,
Is it possible to implement the iOS application to track the iBeacon Component after closing the application(Background processing).
Please provide any example...
Hi Team,
To implement iBeacon what are the things to be take care at the peripheral side.
Whether the code for advertising the peripheral in "CoreBluetooth" and "CoreLocation...
Hi, I have both the nRF8001 dev kit and the nRF51822 Eval Kit (EK). We are using the nRF8001 for most of our project with the BLE Arduino SDK. But I wanted to just load a...
Hi,
What is the suggested method to change a pending request, and make it earlier than previously requested, without closing and reopening the session?
For example,...
Hi,
I am using a custom pcb with a nRF51422 chip, and trying to setup ANT communication between 2 modules, but the sd_ant_channel_id_set call returns an invalid address...
Hi,
To use bidirectional continuous scanning mode in ANT, I have to transmit Extended Broadcast/Acknowledged/Burst messages using ANT Msgs 0x5D, 0x5E, and 0x5F (ANT Message...
We are preparing to get BT qualification for our product, developed with the 6 stack now, however want to update to 7 when it is finally released. A comment from the testing...
Hi,
While access sd_ble_gattc_write api, I got an error code 0x00000011. If I check nordic document for sd_ble_gattc_write error code, I can't find any error code with...
I would like to use nRF2460 in my project (Hearing Aid for elder people).In that I need to transmit the data from a mic/line in to >30 receivers within a range of 100 yards...
I'm using nRF51822 and i want to send a notification to the central to notify it for the changing of a characteristic value (major_value) after using the sd_ble_gatts_value_set...
I currently have a custom service emulating the batterey service. I have added an extra characteristic to recieve data from the central in the same way as ble_app_uart. the...
Like explained in this tutorial , on master control panel I do File-> Flash Programming and reprogram the dongle, which then turns on one more LED on the dongle. But, I still...
I'm using SDK 7.1, PCA10028 eval board, SD110, MCP 3.8.0.7
I've compiled and loaded the dfu_dual_bank_ble_s110 project into my PCA100028 board. It shows up in the MCP as...
Hey,
I use ESB protocol on nrf51822. I am using one Pipe currently I can achieve only 183 Kbps, I read that i can achieve 1Mbps data rate if we use ESB. I have few questions...
I understand that it is possible to set a static passkey on the nRF51822.
However, what I would like to do is handle the verification of the user-entered passkey myself...
Hello all,
I am completely new to BLE and would like to make a sensor network with nRF51822 ( 1x S120 as center node and 8x S110 as slaves) I have been reading the content...
I am trying to make my NRF 51 advertise forever till someone connects. I have based myself on the ble_uart example where it uses fast advertising with 40 ms intervals for...
Hi,
Last year, I heard that nordic semi will release a SoftDevice for central that supports mulitple packets per interval time until June, 2015.
For now, I guess s120...
My understanding so far is that the input buffer of GPIO is disconnected by default and we can keep it disconnected for saving power when the pin is configured as output....
Hello,
I just read this paper "High speed data streaming with nRF24L01 " where we can achieve 1.6 Mbps Data Rate in clean RF environment. I am currently using nrf51822 in...
The documentation for ble_evt_hdr_t says that the evt_len field is
Length in octets excluding this header.
However as far as I can tell it's actually the length...
