We're looking for a Nordic nRF51822 based low profile/small USB dongle that we can use for our iBeacon software.
It would need to come complete with casing and the ability...
Hi all,
i want to establish connection between two threads in cmsis-rtos, can i use
1) semaphore to do this?
2)message queue should be used or any other ipcs can be...
Hi,
I have two CPU in our product. (STM32F2 and Nordic nrf51422).
I use serialization function to link those two CPU(refer to ble_s110_serialization sample)
But I find...
Hi,
My behavior is as follows
Turn on my device(use 51422) and advertising(2 Service and 3 Characteristic)
Turn on my cell phone(Samsung Note3),scan my device...
Hello:
I used analog IIC write MPU6050. Again after power download programs, mpu6050 can run up there ACK response. But the debug will not run. Simulation IIC because no...
Hello!
How can I communicate with my nRF24L01+ and nRF51822 at the same time. I can set up same channel, CRC-mode and I don't use ESB. But what about address? How do I set...
Hi all,
i want to know answer related to following question
1)what is use of uicr?
2)if i place some value in uicr and then change the image,then is there will be change...
I have been working on making at least 1us Timer interval(expect faster than 1MHz) using interrupt.
To do this we need to set the prescaler of Timer to 4, since formula...
Hello, sorry if this is a stupid question, but i'm fairly new to BLE (nRF51822), and even newer at report descriptors.
I'm using a nRF51822, SDK6.0.0 and S110 7.0.0.
In...
I saw softdevice no memory every several times, according to spec, softdevice use 8k, and app use 8k, are they share this 16k memory or no sharing, each use 8k, and reduce...
I am working on an application and need to get the exact time that the master node receive advertising from the slave node. I tried with PPI and it's ok to capture the Radio...
My PCA10001 was working(running the heart rate monitor example) from the coin cell. After it ceased to work, I assume the cell was flat, but on replacing it the PCA10001 still...
Hello,
i'm trying to get running nRF51 on Arduino IDE. I have forked RFduino at the moment github.com/.../RFduino
With SDK i can compile a startup library and an simple...
I am having a lot of trouble using the new 4.3 Android API. I am trying to develop an application for the Android that will communicate via BLE to a Nordic device. I have...
Hi,
I'm using a 51422 with a s210/s310 softdevice. I have some nodes that must exchange some independent data. So I configured the communication to be an independent bidirectional...
Hi,
I am using SDK6.1 and SD7.0 for our application. I would like to know how to implement the static PIN type pairing?
I have searched Nordic's developers zone and found...
Hello,
I am new to nRF51822, and trying to make a simple application for master - slave data transfer.
I want to know how Much time passes from the start of the device until...
i want to prevent somebody to copy my app by SWD interface,so i set RBPCONF register in main application,but i find that it is no use writing RBPCONF register.
First ,i write...
Hi all,
I am new to nRF51822, and trying to make a simple application for device-to-device data transfer.
I have tried the "ble_app_uart" example, which is for device...
I compiled a new HEX for the pca20006 Beacon based on the ble_app_uart project for the pca10001 (remapped the LEDs and buttons), but when I load the beacon using OTA DFU,...
I compiled a new HEX for the pca20006 Beacon based on the ble_app_uart project for the pca10001 (remapped the LEDs and buttons), but when I load the beacon using OTA DFU,...
