We're looking for a Nordic nRF51822 based low profile/small USB dongle that we can use for our iBeacon software.
It would need to come complete with casing and the ability...
Hi all,
i want to establish connection between two threads in cmsis-rtos, can i use
1) semaphore to do this?
2)message queue should be used or any other ipcs can be...
Hi,
I have two CPU in our product. (STM32F2 and Nordic nrf51422).
I use serialization function to link those two CPU(refer to ble_s110_serialization sample)
But I find...
Hi,
My behavior is as follows
Turn on my device(use 51422) and advertising(2 Service and 3 Characteristic)
Turn on my cell phone(Samsung Note3),scan my device...
Hello:
I used analog IIC write MPU6050. Again after power download programs, mpu6050 can run up there ACK response. But the debug will not run. Simulation IIC because no...
Hello!
How can I communicate with my nRF24L01+ and nRF51822 at the same time. I can set up same channel, CRC-mode and I don't use ESB. But what about address? How do I set...
Hi all,
i want to know answer related to following question
1)what is use of uicr?
2)if i place some value in uicr and then change the image,then is there will be change...
To all successful developers.
I want to write some predefined parameters into the stack. So the problem is the adress.
Example: The nRF51 is part of a medical device....
hi,
is it possible that we can use s120 stack as a central, at this stage to work with our customized profiles?
or it will support only SIG profiles
regards & thanks...
Hello,
I've completed the ble iBeacon like application we are working on, with some custom GATT services/characteristics as well.
When I use LightBlue on a MacBookPro...
There is a check box on nRFgo Studio, Lock entire chip from readback. But a lot of chip can not burn one by one
Can I use AES block encryption to do this?
Hi
We are investigating Hong Kong certification for our nRF9E5 based equipment in the 868 band
The snag seems to be that required channel centre frequencies are "odd...
Hi,
My setup is a nRFgo QFAA FA with S110 v.6.0.0 and Motherboard. I am using the latest SDK 5.1.0. The Master Control Panel drives the nrf51822 USB development dongle...
Hi,I have a Nrf8001 module, use a arduino to control it.
Now,I can use this module to connect IPHONE APP(BLE Probe and LightBlue),sending and reciving data are all ok,the...
Hi Nordic Devs,
First, thank you for excellent documentation and sample code for use with your hardware. It's been tremendously useful already!
I'm pleased to own an...
Hi,
i have some trouble with my watchdog in application. If i does a System_reset (no SD Method because i disabled it before) it sometimes top at this point and does nonsense...
Hi,
We'd like to using nRF51822 to setup an environment which have 2 peripherals and 1 multi-connection central.
Peripheral 1 : reading some data from the car(OBDII...
Hi, we add two characteristic as TX/RX.
We are ready to use them to transmit data and receive data with phone
One for transmit the control command and get respond command...
We have hardware that uses the nRF905 transceiver that inputs different addresses into the nRF905 TX messages based on the specific unit (TX_ADDRESS varies based on unit serial...
Hello
We have devices who uses nRF905 for transmissions between them. When we receive messages we use the AM and DR signal to determine if a message is read correctly. The...
GPIOTE gives us 4.
LPCOMP gives us 1.
What else?
I am working on something related with external interrupts.
Doesn't have problem in my project, but I just always...
