Hi,
I have two CPU in our product. (STM32F2 and Nordic nrf51422).
I use serialization function to link those two CPU(refer to ble_s110_serialization sample)
But I find...
Hi,
My behavior is as follows
Turn on my device(use 51422) and advertising(2 Service and 3 Characteristic)
Turn on my cell phone(Samsung Note3),scan my device...
Hello:
I used analog IIC write MPU6050. Again after power download programs, mpu6050 can run up there ACK response. But the debug will not run. Simulation IIC because no...
Hello!
How can I communicate with my nRF24L01+ and nRF51822 at the same time. I can set up same channel, CRC-mode and I don't use ESB. But what about address? How do I set...
Hi all,
i want to know answer related to following question
1)what is use of uicr?
2)if i place some value in uicr and then change the image,then is there will be change...
It used to work, but now it says "Connected" but the rest of the GUI never changes and the mouse just shows a busy spinner. Here's the log file:
0;13:45:18.9900 [MainThread...
Hi all!
My question is:
My own application is built based on the example "ble_app_template", and according to the nrf51 SDK - Examples - BLE Peripheral, this example...
Hello,
we have bought a bmd340 low energy module that we mounted on a selfmade breakout board. Now we want to read an analog value into the bluetooth module. How can we...
In the "Getting Started->Integrating Mesh into nRF5 SDK Examples" documentation for nRF Mesh SDK v3.2.0 it is stated that nRF5 SDK integration is only tested with nRF5 SDK...
Hi. I want to use nRF52840 as a gateway(connected to cloud via Ethernet). I have to transmit a vast number of nodes' data to the cloud via the gateway. To begin with I can...
Hi Sir/Miss,
We want to test advertising interval time of peripheral device to follow APPLE accessory guideline.
We found some topic on forum, it mentions that uses...
I have a custom board. It has its Tx and Rx combined into one wire bus. I am able to transmit data on the bus. But I am unable to receive any data on the board. This is because...
I have nrf9160dk. I want to give AT commands to the sdk through the processor instead of giving it from the PC i.e want to program the processor in a way so that we don't...
For testing direct advertising i used sdkv10 keyboard example, but when im disconnected device form nrf connect manually its resetting. I debug code found that in BLE_ADV_EVT_PEER_ADDR_REQUEST...
hello
I am a newbee in BLE dev.
I try to connect the sensor to the Adafruit board thrut BLE. The sensor is Sensor it is saw on nrf connect iOS as
I mod the HRM central...
Hi,
I am try to configure internal RC (LFCLK) but device hang in "sd_softdevice_enable(&clock_lf_cfg, app_error_fault_handler);" API.
Changed in "sdk_config.h" to enable...
Hi
When we enable the ADC on the nRF9160, we se a considerable rise in current consumption in standby mode, from sub-100 µA to several hundreds of µA (~400 µA). How do we...
Now that most or all of the Nordic nRF5 SDK is covered by the permissive 5-clause Nordic license (as of June 2017: https://devzone.nordicsemi.com/nordic/nordic-blog/b/blog...
Hi
we are working on ble_nus_c multilink implementation and had problems when more than 1 server is connected: we've noticed that data get mixed between servers.
when...
Hello,
I am using nRF52832, SDK_15.3.0, S132 SoftDevice and Segger for flashing the image.
Is there any sample code integrated with HDC2010 Temperature & Humidity...
