Hi Team,
To implement iBeacon what are the things to be take care at the peripheral side.
Whether the code for advertising the peripheral in "CoreBluetooth" and "CoreLocation...
Hi, I have both the nRF8001 dev kit and the nRF51822 Eval Kit (EK). We are using the nRF8001 for most of our project with the BLE Arduino SDK. But I wanted to just load a...
Hi,
What is the suggested method to change a pending request, and make it earlier than previously requested, without closing and reopening the session?
For example,...
Hi,
I am using a custom pcb with a nRF51422 chip, and trying to setup ANT communication between 2 modules, but the sd_ant_channel_id_set call returns an invalid address...
Hi,
To use bidirectional continuous scanning mode in ANT, I have to transmit Extended Broadcast/Acknowledged/Burst messages using ANT Msgs 0x5D, 0x5E, and 0x5F (ANT Message...
We are preparing to get BT qualification for our product, developed with the 6 stack now, however want to update to 7 when it is finally released. A comment from the testing...
What is the best way to minimize transfer in progress errors when trying to send ANT messages? I am using the S310 stack on an nRF51422. I have a busy ANT channel that is...
https://github.com/bjornspockeli/custom_ble_service_example
I am currently following this example with SES on my NRF52840 DK (PCA10056). I copied the ble_app_template example...
Are there any recommended alternatives (& nordic plugins) to the discontinued Bluetooth Developer Studio? I'm looking for a tool to make the process of creating custom GATT...
Hi! I want to copy data from internal flash to a statically allocated buffer in RAM. I get a DACCVIOL hard fault try to do this by memcpy. The hard fault depends on the number...
I need to send 5 sensor values received over SPI to an app over BLE about 5 times a second. I also need to send a few configuration parameters from the app back to the nrf52...
I am using nRF 52 DK connected to Arietta with ARM Linux (4.2.6) 32 bit.
when I was trying to install "vcpkg" using "./bootstrap-vcpkg.sh", I am getting some errors as shown...
I have a phone app which talks to my peripheral device running the nrf52832 and so I will eventually add another peripheral device which ideally can communicate directly to...
Hello everyone!
I'm working on a project where there are 2 microcontrollers: the Nordic nrf52832 and a 3rd-party uC (can't disclose it). A protocol to transfer the firmware...
I feel confused about bearer. what's the difference between mesh-bases bearer and PB-ADV bearer or PB-GATT? there is little knowledge about mesh-bases bearer within mesh profile...
Good afternoon,
At the place I'm working there's 2 main projects using the nordic SDK, while one runs on the 12.3 version, the other is very outdated and still runs on...
Hi,
I'm having a problem at the moment with code based on Espruino on nrf52.
I connect as follows:
ble_gap_scan_params_t m_scan_param;
memset(&m_scan_param, 0,...
I've seen a few post that have similar issues but none that solve my problem.
I have two uarts (uarte0 and uarte1).
I disable them before going to sleep.
I wake with...
Hello,
I cannot successfully flash an nRF9160-Dk to a usable AT modem state using a brand new install of nRFConnect on Windows10, following this Blog post guidance - https...
I am working on 802.15.4 using nrf52840 and sdk 15.2. I want the receiver node to scan the network for beacons transmitted by the transmitter node for 100ms, go to sleep for...
So its seems nrf9160 docs recommend having VDD_GPIO only at 1.8v ... that running at 3.0v (or 3.3v) will compromise LTE performace.
I have 3.3v rail and 3.3v SPI device...
