My goal is to control a RC toy drone (4-ch 2.4GHz) from a PC. I've seen some hacks (for example dzlsevilgeniuslair.blogspot.com.br/.../more-toy-quadcopter-hacking.html) using...
Hi Team,
Is it possible to implement the iOS application to track the iBeacon Component after closing the application(Background processing).
Please provide any example...
Hi Team,
To implement iBeacon what are the things to be take care at the peripheral side.
Whether the code for advertising the peripheral in "CoreBluetooth" and "CoreLocation...
Hi, I have both the nRF8001 dev kit and the nRF51822 Eval Kit (EK). We are using the nRF8001 for most of our project with the BLE Arduino SDK. But I wanted to just load a...
Hi,
What is the suggested method to change a pending request, and make it earlier than previously requested, without closing and reopening the session?
For example,...
Hi,
I am using a custom pcb with a nRF51422 chip, and trying to setup ANT communication between 2 modules, but the sd_ant_channel_id_set call returns an invalid address...
Hi,
To use bidirectional continuous scanning mode in ANT, I have to transmit Extended Broadcast/Acknowledged/Burst messages using ANT Msgs 0x5D, 0x5E, and 0x5F (ANT Message...
hi all, i am using the uart with it's dma to transfer data into the nrf9160, but some of the data is lost in it's way. here are some examples of the loss count in bytes from...
Hello,
I'm using several nRF52840 boards to setup a bluetooth mesh network. Im using the python script "interactive_pyaci.py" to setup the mesh. The mesh is working and...
Hi, As the title asks, I am using the lte_ble_gateway example project on the nRF9160 DK. I am able to connect one nRF52840 DK to the nRF9160 DK over BLE. I am trying to connect...
We have a board that has become unresponsive to programming. It worked well to program about 4 times and then is no longer responding to the J-Link device. The application...
Hi,
I tried implementing serial communication between nrf52832 and HT1632.It didnt work.In HT1632 data sheet it has given following specifications
will nrf52832 supports...
I am trying to build the simplest nRF52 BLE Peripheral application (Lightbulb use case). I am facing below mentioned errors:
Building ‘ble_lightbulb’ from solution ‘ble_lightbulb_pca10040_s132...
Dear all,
I'd like to use 2 spi and 1 i2c at the same time. Can nrf52 support? I read some thread said that only using 1 spi and i2c or 2 spi. Please advice.
regards...
I'm using SAADC like this:
And I'm not getting the done event. I've also tried not low power mode.
If I place a breakpoint in nrfx_saadc.c nrfx_saadc_irq_handler, after...
I'm compiling a custom application using the CMake scripts in the nRF mesh SDK , and I'm trying to print floats using vsnprintf (I'm guessing the problem is the same as with...
Hi,
We are using nRF52 DK tool to sniff BLE data. We we using Wireshark plugin to interface nRF52 DK tool. nRF52 is updated with latest firmware. We keep the tool in between...
Hi,
we are porting code of our project from SDK 14.2 to SDK 15.3.0, and have encountered unexpected behavior from the fstorage module. Even though SoftDevice and BLE stack...
I'm trying to work with the PC-BLE-Driver with the connectivity firmware. I've loaded the connectivty firmware and the application appears to connect to the board. But I'm...
Hi,
I working on the module developed based nRF52840.
I would like to clarify some doubts regarding the TX power of the chip.
The TX power value is higher at the temperatue...
I think there are should be smartphone cpu with bluetooth 5 long range mode support.
for example Qualcomm Snapdragon
Qualcomm Snapdragon 439
Qualcomm Snapdragon 710...
Hi all,
I am looking for some advice on how to implement a couple of extra characteristics(Related with battery) with the Battery Service apart from the usual Battery Level...
