Hi, I have both the nRF8001 dev kit and the nRF51822 Eval Kit (EK). We are using the nRF8001 for most of our project with the BLE Arduino SDK. But I wanted to just load a...
Hi,
What is the suggested method to change a pending request, and make it earlier than previously requested, without closing and reopening the session?
For example,...
Hi,
I am using a custom pcb with a nRF51422 chip, and trying to setup ANT communication between 2 modules, but the sd_ant_channel_id_set call returns an invalid address...
Hi,
To use bidirectional continuous scanning mode in ANT, I have to transmit Extended Broadcast/Acknowledged/Burst messages using ANT Msgs 0x5D, 0x5E, and 0x5F (ANT Message...
We are preparing to get BT qualification for our product, developed with the 6 stack now, however want to update to 7 when it is finally released. A comment from the testing...
What is the best way to minimize transfer in progress errors when trying to send ANT messages? I am using the S310 stack on an nRF51422. I have a busy ANT channel that is...
I'm running into a weird timing issue with a nRF24L01+ which I'm not quite sure how to work around in the general case. The basic setup is two radios, A and B. Auto acknowledgement...
Hi,
We want to send our pre-production ready product for compliance testing. Selected testing laboratory told us " Conducted sampls should be set in continuous transmit...
Dear All,
so we have an embedded SoM running OpenWRT and I was wondering if I can make use of nrfutil even if not connecting a nRF52 via USB but via UART.
What I want...
So as far as I can make out, when I load a new application into the flash, the NRF52 will attempt to first load a secondary memory space and if successful, it will then replace...
Hi,
Right now i am using Blinky example in Peripheral section of SDK15 (S140). I would like to enable Coded PHY (BLE_GAP_PHY_CODED) instead of default setting (BLE_GAP_PHY_1MBPS...
Hi, I have problem with timer in nrf52810. My TIMER2 counts very slow. I declared it as NRF_DRV_TIMER_INSTANCE(2); and config struct is:
.frequency = NRF_TIMER_FREQ_16MHz...
Hi ,
I can compile and use the UART example but when I try to use it in my project I get some linking errors
I have copied and past all the sdk_config.h file to my project...
I am waiting for my custom pcb based on the nrf52832 to be ready and I want to test the flashing process. Is it possible to program a nrf52 DK with another nrf52 DK using...
Hello,
I was wondering if there is some way to program a device to act like a BLE slave, which would sleep and periodically wake up to stay in receive mode for a certain...
Hello, I'm confused what the NRF51422 uses for it's digital IO reference. So for example, If I use a 3.0V coin cell battery through its DC/DC converter: 1. What voltage does...
I download the SDK at https://www.nordicsemi.com/eng/nordic/Products/nRF5-SDK/nRF5-SDK-zip/59011 . When I used "nRF5_SDK_15.0.0_a53641a\examples\ble_central\ble_app_uart_c...
Hi,
I am using SDK10---->ble_app_uart--->pca10028--->s110 for non-invasive GLUCOSE measurement. I checked nrf_adc.h file & used adc_sample = nrf_adc_result_get(); for getting...
I am using nrf52832 development kit and softdevice v5.0.
I am using this code which I have attached.
I have added all require files.it might be not showing to you because...
My current setup is this:
I have a nRF51822 beacon (tiny coin cell beacon) advertising with its default settings. I have another board, a nRF51822 Development Kit, that...
Hi,
I have a customer request regarding ISP1507 module (with nRF52832 integrated) and battery information.
Customer want to have battery information using LED (bicolor...
