Hi, I have both the nRF8001 dev kit and the nRF51822 Eval Kit (EK). We are using the nRF8001 for most of our project with the BLE Arduino SDK. But I wanted to just load a...
Hi,
What is the suggested method to change a pending request, and make it earlier than previously requested, without closing and reopening the session?
For example,...
Hi,
I am using a custom pcb with a nRF51422 chip, and trying to setup ANT communication between 2 modules, but the sd_ant_channel_id_set call returns an invalid address...
Hi,
To use bidirectional continuous scanning mode in ANT, I have to transmit Extended Broadcast/Acknowledged/Burst messages using ANT Msgs 0x5D, 0x5E, and 0x5F (ANT Message...
We are preparing to get BT qualification for our product, developed with the 6 stack now, however want to update to 7 when it is finally released. A comment from the testing...
What is the best way to minimize transfer in progress errors when trying to send ANT messages? I am using the S310 stack on an nRF51422. I have a busy ANT channel that is...
I'm running into a weird timing issue with a nRF24L01+ which I'm not quite sure how to work around in the general case. The basic setup is two radios, A and B. Auto acknowledgement...
Hi,
I need help with alert notification service. I am working on alert notification example provided in the SDK 12.3.0 with S130. I tried this example on nrf51422 development...
I have tried to use sd_app_evt_wait() to sleep cpu, and use gpiote interrupt to wake up cpu from sleep.
However, gpiote interrupt cannot wake up cpu.
When I use __WFE()...
Hi,
I am trying to send sensor(accelerometer) data through beacon. I am basing my logic on the beacon example. I am putting my sensor data into an array and passing it...
Hi,
I have an nRF51 DK, found here www.nordicsemi.com/.../nRF51-DK .
I am using SDK V11.0 and S130 V2.0.
I am developing on a Linux machine.
I can compile and run...
Hi.
I'm using the Power Profiler Kit and the PPK desktop application to log the power consumption of my device. This works well for short time spans.
However, I'd also...
Hi
I'm trying to delete all files with a given file id. Will fds_file_delete() delete all files with a given file id, or just the first one it finds?
thanks
SDK1...
Hi
I'm trying to use fds_record_find() to detect if a record exists in flash storage. After erasing the device (via nrfjprog), flashing the softdevice, flashing the program...
I use an app_timer to periodically update sensor reading in my application. There is a characteristic used to change updating rate by stopping and restarting the app_timer...
Hi,
I work on a project for the nRF52832 with Keil µVision using ARM Compiler V5.06 update 2 and nRF5 SDK 11.
In a module I allocate quite some memory using malloc(...
For the BLE GAP advertising flags byte in the advertising data, we have the following options:
/**@defgroup BLE_GAP_ADV_FLAGS GAP Advertisement Flags
* @{ */
#define...
I cannot seem to save the new Device Name value in the nRF51822 beacon.
I am using the mobile app nRF Connect.
This is my procedure:
1).Run nRF Connect on Android device...
Hi Nordic Team;
I am using nrf51822 devices with sdk12.3.0. I am using buttonless dfu example without any problem with sdk12.3. However, I see that you realese sdk14 that...
We're considering nRF51/52 to implement a specific BLE application. We need the nRF51/52 go to sleep if a BLE collision signal or interference on an advertising channel has...
Hi,
I'm using nRF5_SDK_13.0 on nRF52840 based on ble_app_hrs_rscs_relay example. I use it to connect a bluetooth 4.0 device and it's ok now. Also I have a bluetooth 5.0...
