Hi,
My behavior is as follows
Turn on my device(use 51422) and advertising(2 Service and 3 Characteristic)
Turn on my cell phone(Samsung Note3),scan my device...
Hello:
I used analog IIC write MPU6050. Again after power download programs, mpu6050 can run up there ACK response. But the debug will not run. Simulation IIC because no...
Hello!
How can I communicate with my nRF24L01+ and nRF51822 at the same time. I can set up same channel, CRC-mode and I don't use ESB. But what about address? How do I set...
Hi all,
i want to know answer related to following question
1)what is use of uicr?
2)if i place some value in uicr and then change the image,then is there will be change...
It used to work, but now it says "Connected" but the rest of the GUI never changes and the mouse just shows a busy spinner. Here's the log file:
0;13:45:18.9900 [MainThread...
Hi all!
My question is:
My own application is built based on the example "ble_app_template", and according to the nrf51 SDK - Examples - BLE Peripheral, this example...
Hi,
I am using ancs service to get some information of my iphone.
I use nRF51822 microcontroller and Nordic suggests to use the new SDK (5.2) for new microcontroller...
Hi all
I'm working on a custom board using gcc and eclipse.
My primary problem is I'm fighting with the ld settings for the secure bootloader.
I activated the RTT which...
Hi,
I want to write calibration and configuration datas in to flash and read it back. By using sd_ble _flash_write API function , I can write up to 520 words(520* 4 bytes...
Hi, all!
nRF51822 had been used in my project, because of dual bank bootloader and softdevice, the
internal flash memory was not enough for the application. I want to...
Hi there,
I need to add more the function based on Bluetooth, and I need the better security of the function. However, I do not want others read flash data freely and I hope...
Hi
I'm preparing for some tests and I'm wondering where I can find information about what the expected percentage error rate should be?
Right now with 2 nrf boards connected...
Hello to all nordic jedi masters!
I have made an observation, on which I would like your confirmation.
My combo is: nrf52832 + SDK 11 + SD132.
Will my application ...
I'm currently writing my thesis, and my goal is to establish a network protocol like IP. We need to transmit about 200kB of data between 2 or more nodes once every 10-30 minutes...
I am programming a device with a NF52 that uses a hall effect switch o enter/exit sleep mode when BLE is in advertising mode. When connected, It will generate a separate BLE...
Hello,
i have a strange behaviour on a board with nRF52. The board is flashed with SD 4.0.2 and bootloader.
On Keil If i load the bootloader with JLink, it runs and...
I'm using nrfutil version 2.0.0 and have noticed a strange bug today when generating a new signed application image for bootloading.
If I have a version number of 0207...
hello , I am new to SPI protocol.I am using NRF52 DK &nRF5_SDK_13.0.0_04a0bfd( pca10040) using keil-5. I want spi master example code. Can any one suggested me where I find...
Hi there,
The S132 SoftDevice for the nRF52832 has grown in size from 0x1F000 for release 1.0.0-2.alpha, to 0x23000 for 5.0.0-3.alpha. It appears that the nRF52840 will...
I have a small PCB I'm prototyping/assembling, based on a nRF52832 with a few sensors. Looking for someone here to help me with writing basic firmware for testing the board...
