Hello:
I used analog IIC write MPU6050. Again after power download programs, mpu6050 can run up there ACK response. But the debug will not run. Simulation IIC because no...
Hello!
How can I communicate with my nRF24L01+ and nRF51822 at the same time. I can set up same channel, CRC-mode and I don't use ESB. But what about address? How do I set...
Hi all,
i want to know answer related to following question
1)what is use of uicr?
2)if i place some value in uicr and then change the image,then is there will be change...
It used to work, but now it says "Connected" but the rest of the GUI never changes and the mouse just shows a busy spinner. Here's the log file:
0;13:45:18.9900 [MainThread...
Hi all!
My question is:
My own application is built based on the example "ble_app_template", and according to the nrf51 SDK - Examples - BLE Peripheral, this example...
Hi,
I am using ancs service to get some information of my iphone.
I use nRF51822 microcontroller and Nordic suggests to use the new SDK (5.2) for new microcontroller...
Dear sirs,
My purpose is to transmit stereo HiFiaudio from one source to two speakers wirelessly.
The speakers have their own power amplifier.
The problem is that the...
Hi I am using Jlink board, when connected to my pc, I can't select nRF5x programming.
Version I am using is 1.20.0.2. I tried the uninstalling everything and installing....
I have been able to get all the MPU based projects to work from this Github site (which has been very helpful!) with the exception of this one.
The accelerometer values...
For a device that has APPROTECT enabled, it is required to use nrfjprog --recover to re-enable access.
What is the mechanism that nrfjprog uses to perform the --recover...
With the nRF52, is the RTT functional when APPROTECT is enabled?
I would expect not since the RTT relies on memory accesses which should be disabled with APPROTECT
Hi,
In SDK11, it was possible to call app_sched_execute() from a function that was itself called from the scheduler:
void app_sched_execute(void)
{
void * p_event_data;...
If you dont have an external 32Khz crystal for the nRF52832, besides the higher power consumption, are there any other issues ? e.g. CPU starvation affecting my app during...
Hi all,
I work with a nrf52, my project send and receive Beacon data.
when i work only with 2 card all works fine but when there are several transmitter and 1 receiver...
I've got an nRF52 application which is based on the nRF OpenMesh github.com/.../ but has been vastly customised. The application either acts as a mesh device and allows a...
As the title，I recently want to use nRF51822 to communicate with SmartCard in ISO7816 interface. but I don't know how to do this.Can anyone share the example code online ...
Hello,
I am using the nrf sniffer from adafruit to pick up ble packets from my NRF52. Everything has been working fine for the past 3-4 months. Yesterday I wanted to test...
I'm trying to create a HID over GATT device that is not a keyboard, nor a mouse. About a week ago, I came close by being able to read some data in an OSX app from the device...
Have project setup to read values from ADC and then run fft_process. Then print them out over uart using NRF_LOG_* statements. However after we call the arm fft functions...
Hello, I am using nrf51822 and SDK11, dual bank dfu ble, S130, 2.0.0.
I made dfu zip file and I modify firmware_crc16 value to the wrong one.
And I zip it again.
But...
hai
i am working with nrf51822 and mbed .
in my application i have requested one page in flash for data store using pstorage.
pstorage_module_param_t param;
param...
