We're looking for a Nordic nRF51822 based low profile/small USB dongle that we can use for our iBeacon software.
It would need to come complete with casing and the ability...
Hi all,
i want to establish connection between two threads in cmsis-rtos, can i use
1) semaphore to do this?
2)message queue should be used or any other ipcs can be...
Hi,
I have two CPU in our product. (STM32F2 and Nordic nrf51422).
I use serialization function to link those two CPU(refer to ble_s110_serialization sample)
But I find...
Hi,
My behavior is as follows
Turn on my device(use 51422) and advertising(2 Service and 3 Characteristic)
Turn on my cell phone(Samsung Note3),scan my device...
Hello:
I used analog IIC write MPU6050. Again after power download programs, mpu6050 can run up there ACK response. But the debug will not run. Simulation IIC because no...
Hello!
How can I communicate with my nRF24L01+ and nRF51822 at the same time. I can set up same channel, CRC-mode and I don't use ESB. But what about address? How do I set...
Hi all,
i want to know answer related to following question
1)what is use of uicr?
2)if i place some value in uicr and then change the image,then is there will be change...
We are trying to communicate to NRF51422 through PC using UART communication. But the programs works fine with nRF51822 Dongle and DK. But it does not works with another dongle...
Hi experts,
I need nrf51822 to send thousands of packets (notification) to Master Control Panel (PC), and expect for high data rate. So, I turned the connection interval...
if initial uart_config() before ble_stack_init(), softdevice_handler_init will be failed!
with SDK 6.0
softdevice_handler_init() will returns 0x00001001 ("NRF_ERROR_SDM_INCORRECT_INTERRUPT_CONFIGURATION...
I am trying to generate code using BDS and the Nordic Plugin 1.2 but I keep getting the following error. I have reviewed the XML but I can't seem to find the issue. Any thoughts...
I've been fighting this bug for a few days now and I thought I'd share what I discovered in the process.
I wanted to set up a couple PWM channels to control a few LEDs...
getting problem in implementing uart. code is here
#include <stdio.h>
#include "boards.h"
#include "app_util_platform.h"
#include "app_uart.h"
#include "app_error.h...
I implemented measuring of Lithium battery level with the help of thread How to measure Lithium battery voltage . I am using nRF51422 with SoftDevice 110 and SDK 9.0.0 and...
Greetings,
I'd like to develop a wireless sensor network based on your products, but have a few concerns based on my lack of knowledge of how Bluetooth LE works.
I've...
We are running FreeRTOS on the PCA10028 development board. We have bumped into an issue where the code asserts if we turn on the FreeRTOS configASSERT functionality. It is...
Hello,
I am using nrf starter kit and nRF51822 DK modules atached. I'm using external usb-com uart modules (based on FT232 chips) for communication with PC (Win7) and hyper...
Hello everyone
i am trying to configure the buzzer int he development board inordert o create the buzzer beep sound i have configured the GPIO pin 14 fir the buzzer so...
The ble-sdk-arduino UART examples (and others?) have a rather convoluted scheme to delay the ChangeTimingRequest until after an ACI_EVT_PIPE_STATUS event indicates that the...
Hey guys,
With the BLE stack initialized, I’m not able to get the power down to where I’d expect with nRF51822, running SD S110 8.0 and SDK 9-2.
I’ve tried three, very...
