Hi, I have both the nRF8001 dev kit and the nRF51822 Eval Kit (EK). We are using the nRF8001 for most of our project with the BLE Arduino SDK. But I wanted to just load a...
Hi,
What is the suggested method to change a pending request, and make it earlier than previously requested, without closing and reopening the session?
For example,...
Hi,
I am using a custom pcb with a nRF51422 chip, and trying to setup ANT communication between 2 modules, but the sd_ant_channel_id_set call returns an invalid address...
Hi,
To use bidirectional continuous scanning mode in ANT, I have to transmit Extended Broadcast/Acknowledged/Burst messages using ANT Msgs 0x5D, 0x5E, and 0x5F (ANT Message...
We are preparing to get BT qualification for our product, developed with the 6 stack now, however want to update to 7 when it is finally released. A comment from the testing...
What is the best way to minimize transfer in progress errors when trying to send ANT messages? I am using the S310 stack on an nRF51422. I have a busy ANT channel that is...
I'm running into a weird timing issue with a nRF24L01+ which I'm not quite sure how to work around in the general case. The basic setup is two radios, A and B. Auto acknowledgement...
Hi,
Is it possible to enable the transmission of 2 bytes of preamble and use the TIFS register to force a delay to transmission when in proprietary 2Mbps mode?
Thanks...
Hello, I'm using SDK 16.0, softdevice s132 v7.0.1, I'm sending the device to SystemOFF and configuring a pin to wake it up with
nrf_gpio_cfg_sense_set( IMU_INT2_PIN , NRF_GPIO_PIN_SENSE_HIGH...
Hi,
I am using a 52832 part as a peripheral communicating with a central running on an ESP32. It operates in the following manner:
1. When it is active, the peripheral...
I am getting a "Stopped by vector catch". This isn't particularly informative. How does one find the code location where the fault is generated?
Thanks
Hello everyone,
I just started learning BLE. I want to develop an application that gets RSSI from a beacon and displays the magnitude of RSSI using 4 built-in LEDs.
Beacon...
We want realize mesh network to mibile phone clients using BLE5
We assume we are have to use 3 types of devices:
1) Mobile phone/pad with built-in BLE5
2) Access points...
In our use case we are using the nRF9160 in eDRX mode with an eDRX interval of 40.96sec.
I'm noticing that the power required to transmit a message varies widely between...
Hello, I am pretending to catch BLE packages with nrf52840 dk with Visual Studio Code or Clion, which one is the best for this kind of programm? Thanks
Hello,
I'm looking for some documentation, and maybe a complete list of possible data I can read over MQTT from a Nrf Thingy 91. Specifically, we're using these fields right...
Hi all,
I have read about the local binding between the endpoints (same device) and i wanted to implement this type of binding in a device which has 2 endpoints (switch...
Hello,
I am using the nrf9160 DK board ver 0.9.0 running the latest version of the asset tracker application. I am wanting to switch the serial ports off to measure the...
This discussion got mixed up with a discussion about what Nordic means by a 'system attribute' (which is still not clear). In any case, in that discussion I was trying to...
Hi, I take the tutorial here: https://github.com/NordicPlayground/nRF5x-custom-ble-service-tutorial
Because I have the SDK16 I made same mofification.
1) I comment all...
Hi
I want to know the time taken(in us) by a code snippet. I had a look at app_timer functionality with the help of this post . But the timer value always shows 0. I am...
