My goal is to control a RC toy drone (4-ch 2.4GHz) from a PC. I've seen some hacks (for example dzlsevilgeniuslair.blogspot.com.br/.../more-toy-quadcopter-hacking.html) using...
Hi Team,
Is it possible to implement the iOS application to track the iBeacon Component after closing the application(Background processing).
Please provide any example...
Hi Team,
To implement iBeacon what are the things to be take care at the peripheral side.
Whether the code for advertising the peripheral in "CoreBluetooth" and "CoreLocation...
Hi, I have both the nRF8001 dev kit and the nRF51822 Eval Kit (EK). We are using the nRF8001 for most of our project with the BLE Arduino SDK. But I wanted to just load a...
Hi,
What is the suggested method to change a pending request, and make it earlier than previously requested, without closing and reopening the session?
For example,...
Hi,
I am using a custom pcb with a nRF51422 chip, and trying to setup ANT communication between 2 modules, but the sd_ant_channel_id_set call returns an invalid address...
Hi,
To use bidirectional continuous scanning mode in ANT, I have to transmit Extended Broadcast/Acknowledged/Burst messages using ANT Msgs 0x5D, 0x5E, and 0x5F (ANT Message...
Hi
I am currently trying to connect the sht31 temperature / humidity sensor. First, I made an implementation based on the twi_sensor example. I did it all, the temperature...
Dear all,
I am quite new to embedded programming and I am looking for a tutorial/example code in order to communicate/configure an accelerometer sensor (LIS2DH12) with NRF52...
Hi,
I am running SDK 15.3, nRF52840 on a custom board, Softdevice 6.1.1 and SES.
When running the secure dfu example I find that the two segments uicr_mbr_params_page...
Hi,
NRF52932, s132.
I am currently migring from SDK 14.0.0 to SDK 15.3.0, I just finished to migrate from SDK 13.2.0 to SDK 14.0.0. The project with my app compile but...
Hi
I want to transfer a text filebetween nrf51 to nrf52 .Is this possible in nrf device. If it is How can i proceed ?. I am using NRF 15.0 SDK.
Please help me on this...
Hi
We are using today nRF52832 and communicate through Nordic UART service (NUS).
Sometimes we would like to transfer files from our device to the app. This is going very...
Hi All,
I have an application running on the nRF52832. From within the application I can store data to 0x2000 2010 - 0x2000 2028 and read the data back after a reboot/power...
Hi,
I need to generate a PWM signal with exact 2.048 MHz. I've just realized that
allows only decimal frequency. Even if I take 16 MHz and toggle it every 7,8,9 still...
Hi,
I have the NRF52 dev kit with NRF522832 chip. I am using SDK version 15.2 and the Segger IDE. I am trying to do OTA programming and have used this tutorial:
https...
I followed the nRF User Guide v2.2 for my nRF dongle and all was Ok up to "Install firmware with SEGGER J-Link point 6 e (loadfile Path\...\sniffer_pca10031.hex)". Got error...
Hi!
I am trying to get this example to work on my nRF9160 board: https://github.com/Rallare/fw-nrfconnect-nrf/tree/nrf9160_samples/samples/nrf9160/spi/
It compiles and...
Hi,
if got the following setup:
Nordic nRF52840 DK (peripheral), custom iOS App (central), nRF Connect Desktop Version + another nRf52840 DK as sniffer.
My Goal: Changing...
Hello,
I need to interface both, an SD card and a smaller (~4Mb) external flash to the nRF52840.
The SD card will be interfaced using SPI.
For the external flash...
I would like to store some parameters in nordic's non volatile memory and be able to restore them after power off.I am using the soft device s130.
I have checked both examples...
I have made a HDI 4-Layers PCB. I referenced the example PCB, but my board it do not work.
The softdevice is:s132_nrf52_6.0.0_softdevice.hex
The example code is: ble_app_uart...