Hi,
What is the suggested method to change a pending request, and make it earlier than previously requested, without closing and reopening the session?
For example,...
Hi,
I am using a custom pcb with a nRF51422 chip, and trying to setup ANT communication between 2 modules, but the sd_ant_channel_id_set call returns an invalid address...
Hi,
To use bidirectional continuous scanning mode in ANT, I have to transmit Extended Broadcast/Acknowledged/Burst messages using ANT Msgs 0x5D, 0x5E, and 0x5F (ANT Message...
We are preparing to get BT qualification for our product, developed with the 6 stack now, however want to update to 7 when it is finally released. A comment from the testing...
What is the best way to minimize transfer in progress errors when trying to send ANT messages? I am using the S310 stack on an nRF51422. I have a busy ANT channel that is...
I'm running into a weird timing issue with a nRF24L01+ which I'm not quite sure how to work around in the general case. The basic setup is two radios, A and B. Auto acknowledgement...
I am using mbed library to get leg up on development.
This is the first time I am writing any MCU application and it sure makes things a lot easier.
I am using nRF51822...
I can not find the datasheet for Preview Development Kit, the only avialble documentaion is the User Guide and nRF52840 Objective Product Specification. What i need is the...
Hi,
We are integrating a 3rd party device with our application and while we were parsing advertising data, we found the same data received in Android at 3rd and 4th index...
pm_peer_data_remote_db_store() stores an array of ble_gatt_db_srv_t.
pm_peer_data_remote_db_store() calls pm_peer_data_store(), which requires a buffer whose alignment...
Hi, I downloaded the latest SDK V12, coped the example HEX from the BLE Beacon and it worked fine. I tried to then compile using Keil, it compiled,
when upload again blinky...
Hi all,
I am using PCA10040 (nRF52832) and I want to create a ble mesh network. I know that this SDK contains some examples for mesh, but I am not able to find something...
Hi!
I have an implementation running with a peripheral sending notifications to a central at 27.5 ms. They are both configured with HIGH BW. Sending of notifications is...
Hi,
PTX:
based on the SDK11 "\examples\proprietary_rf\esb_ptx\pca10040\blank\arm4\esb_ptx_blank_pca10040.uvproj",
what I changed is delete the "nrf_delay_us(50000)" in...
I am simply trying to add a custom service to the HRS example. When I build in regular s132 armgcc it works no problem shows my blank service with nothing special. however...
Hi,
How can i disable peer manager from the buttonless DFU example. if just disable the peermanager by removing the code and editing sdk file, its not working.
i am using...
Hi All,
I am working on BLE+SD card.I am getting following error:-
*** Using Compiler 'V5.06 update 4 (build 422)', folder: 'C:\Keil_v5\ARM\ARMCC\Bin'
Build target...
I have a app that stores some calibration information in flash (1 page at 0x7F000)
When I booted now I noticed it has replaced it with "DEADCODE" following some hex number...
SDK version 12.2 and SoftDevice 132 and Dev. Board 10040
I am trying to run the ble_app_beacon example with NRF52832 DK. I have imported the IAR project into Segger Studio...
Hi,
I bought the nRF52840 in april. The problem is that my iPad doesn't detect the nRF52840. Also, when Itry to upload a .hex file on it, the board tells me that the upload...
