Hi Team,
To implement iBeacon what are the things to be take care at the peripheral side.
Whether the code for advertising the peripheral in "CoreBluetooth" and "CoreLocation...
Hi, I have both the nRF8001 dev kit and the nRF51822 Eval Kit (EK). We are using the nRF8001 for most of our project with the BLE Arduino SDK. But I wanted to just load a...
Hi,
What is the suggested method to change a pending request, and make it earlier than previously requested, without closing and reopening the session?
For example,...
Hi,
I am using a custom pcb with a nRF51422 chip, and trying to setup ANT communication between 2 modules, but the sd_ant_channel_id_set call returns an invalid address...
Hi,
To use bidirectional continuous scanning mode in ANT, I have to transmit Extended Broadcast/Acknowledged/Burst messages using ANT Msgs 0x5D, 0x5E, and 0x5F (ANT Message...
We are preparing to get BT qualification for our product, developed with the 6 stack now, however want to update to 7 when it is finally released. A comment from the testing...
What is the best way to minimize transfer in progress errors when trying to send ANT messages? I am using the S310 stack on an nRF51422. I have a busy ANT channel that is...
I was playing around with examples and decided to implement a custom service that sends the RSSI as a single-byte characteristic value. Here's the init function:
static...
Hi,
I'm trying to connect to BLE and send data on UART. I'm using nrf51422 with softdevice s310 and SDK v5.2.0.
The following code gives me error 3003 which I figured...
Hi,
I think getting started with the Nordic chips is not as easy as some others.
I would like to know what are the first things that I need to run my code on a Nordic? Especially...
I just got the nRFgo Dev Kit, and going through the set up I see I need a nRF6310 Motherboard, but I can't seem to find anything about it - like were to buy it.
I just downloaded their iccv8cortex trial version and it includes the 51822 as a target. My 5 minute test drive not withstanding, it looks like this might be a good option...
How to reduce power, for bond connections such as cscs services which only requires communication once per second?
Is there a way to manually / automagically turn off the...
Before I call sd_power_system_off(), I do the following:
NRF_TWI0->ENABLE = 0;
NRF_TWI1->ENABLE = 0;
NRF_ADC->ENABLE = 0;
NRF_SPI0->ENABLE = 0;
NRF_UART0->ENABLE =...
Hi
I using nRF51822 ble_app_uart project with softdevice 7.0.
I need to manage my internal flash memory map so i cannot use pstorage libary test main.txt .
So i try...
Hi,
What is the typical range of operation that can be achieved by nRF51822 Bluetooth Smart Beacon Kit ? I know it depends on the Tx power, but can a range of approx 30ms...
I need help choosing between 2 technologies above, my goal is to enable multiple (up to 20) devices exchange small amount of information (around 30 bytes) between each other...
Hello
How many packets can the nRF8001 send in a single connection event? I have seen here, that it is possible to send up to 6 packets with the nRF51822 + Softdevice S110...
Hi, we've been using nRF51822 for developing application and iOS 7.x detect then just fine.
Since I upgraded to iOS 8. Beacons are 'invisible' to our application.
I was...
When I try to use the mergehex tool to combine all three my application never seems to get properly combined.
What I'm doing:
mergehex -m softdevice.hex myapp.hex -o...