Hi,
Will PAN item #56 TWI: TWI module lock-up be fixed in the Rev 3 version of the nRF51822/51422?
Also would you happen to have a time frame as to when the Rev 3 will...
Close Bluetooth in Iphone's settings when IOS/51822 is paired and connected normally.
several seconds later, Open Bluetooth in the settings again, and observe the settings...
Hi,
I am trying to power off and/or disable a RR[0] with no success.
I am Powering OFF the watchdog in main and then successfully POWERing ON in wdt_init but then I...
Is it possible when using the S110 softdevice to limit the maximum number of packets per connection event? I would like to reduce the maximum amount of time the CPU spends...
I am using nRF51422 Evaluation Kit with the latest silicon revision which comes with programmable softdevice. The kit also contains an ANT USB-m dongle. I have followed the...
I tried to do send & receive binary data from bluetooth in ios app.
But i only can send & receive string or ASCII code data in my app, do you have any method or idea can...
Hi,
I tried ble_app_hids_mouse with Android 4.4.2, it can work properly for first time connection. However, it cannot be re-connected after switching Phone's Bluetooth...
We are using an MX25R6435FZNIL0 part on a design with a nRF5340 module and wish to test that 48MHz operation of QSPI is working, we are using the latest master version of...
I am using Keil and trying to debug one of the examples in nrf_SDK_12.3.0 and half of the lines are not accessible in line by line debugging. Those lines where one can set...
HI!
I use flash data storage (fds) to store some user inputs in flash. Everything works fine, but I am surprised by the fact that the function fds_record_update() is not...
Hi All,
Using SDK15.3, NRF52840 USB Dongle.
After a few experiments I would like to clarify my understanding on how the usb bulk write works.
I am currently writting...
I am using Nordic Thingy 91 Kit.
I have uploaded modem and application firmware URL : Nordic Thingy:91 - Downloads - nordicsemi.com
I am facing following problem while...
The following issue is for NCS version 1.4.0 and 1.4.1 for an nRF52840 DK target.
When CONFIG_BT_AUTO_PHY_UPDATE =y for both a peripheral and central, I see in Wireshark...
Hi,
I am using the following snippet in my application. it is working fine sometimes but the other times it's not coming out of the while loop.
can anybody point out the...
I have been struggling to reduce the current on the Nordic Dongle to the sub 3 uA levels that the specs suggest I should be able to achieve.
I am stuck at achieving a 9...
i am trying to determine the current consumption of the nRF9160 when in sleep mode but running LPUART and TWIS.
I see that the Sleep mode (MCU IDLE, MODEM off, RTC on) shows...
Hi all, i want to use CMSIS DSP library for vector/matrix computation.
In NRF connect SDK, there is a "nRF CMSIS DSP examples solution" in the dashboard, however it fails...
Hello,
I have an external flash w25n01gv, I am using this simple spi loopback example to test the spi functionality of nrf9160. I want to read the jedec id of my device...
Does doing DFU again and again on same controller can cause misbehavior of code? I am using BLE + UART + EEPROM in my code and sometimes I face the issue with UART event handler...
Hi,
I'm using NRF52840 to connect my mobile.
I'm using whitelist, following the example. It used to work perfectly for about 1 year.
However - in the last couple...
After starting the program, I do the first calibration and read the data 30 times. The standard deviation is between 2.0 and 2.3. Perform 30 "Calibration -> Read Data" each...
Hi,
Greetings of the day!
I used nRF Connect for desktop to program the nRF52840 device. But I can't lock the program and protect the device using this utility. I installed...
