Hi All,
i would like to know about
1) what is channel in nrf51288?
2) is there any mathematical relationship between channel no and pin no as in ble_app_hrs
example channel...
Hi,
I use UART bootloader SDK example(dfu_dual_bank_hci) to do update firmware on EK PCA10001 board,it can work ok.But i changed the HCI_SLIP_UART_RX_PIN_NUMBER and HCI_SLIP_UART_TX_PIN_NUMBER...
Hi. I have been trying get a notification through ANCS.
I have created an app which is made by modifying ble_app_ancs sample.
It works basically but there is one problem...
Hello,
I'm using the nrf51422 with 210 softdevice.
I'm trying to figure out a way for the receiving slave device to go to sleep when away from the master, but to wake...
To be able to upgrade FW through UART, a bootloader for nrf51822 is required in my project. I have tried out the example bootloader in SDK. But this example is using softdevice...
I followed the forum posts and nan-29 to get eclipse 4.3.2 to successfully connect to JLinkGDBServer via a Segger J-Link EDU on Ubuntu Linux.
I can start the GDB server...
I'm using Softedevice 6.0.0 and SDK 5.2. and Keil 4.7.
I Modified bootloader project so it compiles with both ble and hci transports. Currently I use button_0 and button_1...
I,m using nrf51822 , Softdevice S110 and SDK V10. i have and spi interface with SST26VF064B (8MB flash) . SPI is running at 4MHz frequency and there is 8us delay between each...
I have a new board with a STM32L47 running mbed OS. There is an nRF52811 connected via SPI. I simply want to verify that the nRF52811 is connected properly and can be communicated...
Hi there,
On our test jig, we are using two IO pins of nRF52832 as UART lines that goes to a UART dongle to the PC. When we pull the power plug to the Nordic chip and have...
I deleted nrf-related files and set up nrf programs from a scratch following Get Started Assistant of nRF Connect v3.0.0
I've got this warning when I opened a project by...
This is for a current project on SDK 15 and nRF52832.
My project has several configuration parameters, which exist as BLE attributes.
I'd like to make them persist across...
Hi,
I am study nRFGo Gazell now and I got confused on timer period change in gzll_radio_isr_function().
Per my understanding the Gazell link layer modify timer period...
Using nRF connect SDK V1.0.0
File --> Open nrf connect SDK project
Tools --> Option --> nRF connect
Install all the packages described in "Getting started...
We are evaluating the feasibility of a device using nrf52840 which requires below peripherals:
3 x SPI: For MCU to MCU communication + high-speed data transfer from sensors...
Hi,
I am using nRF51822 controller. And I am using SPI peripheral to read 80 bytes of converted data from an ADC converter.
While reading spi data I realized that there...
Hi,
I have build a application based on the mqtt-simple-sample and successfully integrated TLS.
Now I wanted to measure the floor current in PSM. I did wait some minutes...
Folks,
I have a dev board PCA10040, which is running, I think, soft device s132. Additional load file is:
components/softdevice/s132/hex/s132_nrf52_6.1.1_softdevice.hex...
Dear Team,
I have a problem with one sensor on some boards, the behavior is not clearly reproducible. On some boards, the "device_get_binding("CCS811")" just delivers exit...
Section 18.6.2 of the nRF52832 datasheet (Power-On reset) specifies the following:
A step increase in supply voltage of 300 mV or more, with rise time of 300 ms...
Hello,
I have tried the GPS sample and it worked fine. Now I want to understand the code more in detail und maybe modify the GPS settings.
But I can’t find any documentation...
Hello NRF Team,
Is it possible to change the I2S buffer size on the fly while a i2s transfer is running ? (I Am using nRf52840 with SDK15.2)
I found in the documentation...
