Close Bluetooth in Iphone's settings when IOS/51822 is paired and connected normally.
several seconds later, Open Bluetooth in the settings again, and observe the settings...
Hi,
I am trying to power off and/or disable a RR[0] with no success.
I am Powering OFF the watchdog in main and then successfully POWERing ON in wdt_init but then I...
Is it possible when using the S110 softdevice to limit the maximum number of packets per connection event? I would like to reduce the maximum amount of time the CPU spends...
I am using nRF51422 Evaluation Kit with the latest silicon revision which comes with programmable softdevice. The kit also contains an ANT USB-m dongle. I have followed the...
I tried to do send & receive binary data from bluetooth in ios app.
But i only can send & receive string or ASCII code data in my app, do you have any method or idea can...
Hi,
I tried ble_app_hids_mouse with Android 4.4.2, it can work properly for first time connection. However, it cannot be re-connected after switching Phone's Bluetooth...
I have installed Keil MKD-Lite V 5.10.0.0 and the Segger software (which linked to the Keil IDE). I have tried to install the nRF51 SDK (5 times) and every time iI get the...
Hi, Nordic
I use SDK12.1 with nRF52832, I found one issue:
if I do not program bootloader, nRFgo Studio can program app.
First, erase all flash, then program softdevice...
Hi Everone/Nodiac
I had tried so many threads and previous questions but not bale to get my answer so asking after two weeks.
I am willing to send a string from stm32f4...
Hello,
I currently working with the nRF52832 chip on a custom board. The external clock is a 32MHz clock with +/- 10 ppm. When I use nrf_delay_us or nrf_delay_ms the delay...
Hi all,
I am using a C# application with the masteremulator dll to connect to a nRF51822 with S110 V8.0.0
I can bond with a new device, and communicate with it in a...
In developing the device, for very low battery consumption, I encountered a feature of the implementation Gazell (ESB) protocol.
When I send a packet from the DEVICE (PTX...
Hello,
I am a little bit confused when reading in NRF52 spec that a NVM page is 4KB while block size is 512B. Usually an NVM memory is composed of block made of pages,...
Hi,
I am testing github.com/.../nRF52-fds-example
I am on nrf52832 with sdk 12.2.0 .
I can't seem to make it work.
What i have done:
Separated FDS stuff to separate...
Hi all,
I am trying use the SAADC in blocking mode inside a RTC I am currently using
The issues comes from the example
saadc_blocking_simple
the ADC always give...
I guess this has been mentioned/asked before but you should really do something to enforce the full chip part-numbers to be listed at distributors.
For example, for an...
(Maybe this isn't an ideal place for issues with your web site, but I could see no better one.)
There is a technical non-conformance in your nordicsemi.com domain. In practice...
I've been testing my application and am having an issue opening MasterEmulator sometimes. I need to reseat the nfr51 dongle to clear out the errors I am seeing below. Any...
Hi,
I get error NRF_ERROR_INVALID_PARAM or error 0x12 from sd_ble_gap_connect in central.
I even changed peer_addr.type to 0 (BLE_GAP_ADDR_TYPE_PUBLIC).
When scanning find...
Hi, I'm trying to use an MDBT40 based board as a sniffer using the NRF sniffer firmware. I'm guessing I just need UART -> USB to talk to the chip, so I've hooked it up to...
Hi,
I am trying to figure out the best way to save power on the nrf52. I need to connect with ble about two times per day. The ble should 'woken up' by an accelerator ...
How can I flash both the dfu bootloader and an application, and have the application run after the flash?
As soon as I flash the bootloader, it kicks in doesn't fire the...
