Hi all,
I have an application where an nrf24le1 is communicating serially with another processor, using the UART at 57600 bps. I have multiple identical boards communicating...
after flash DFU program into pca10001 board, com3 is not accessible,
www.dropbox.com/.../Screenshot 2014-04-26 15.41.47.png
even after I erase all, and re upload soft...
Using S120 V 8.0.0.3 alpha, processing a BLE_GATTC_EVT_READ_RSP,
received 0x16 bytes of data but there is more to read. Next call to
sd_ble_gattc_read using the same connection...
Hello：
Why Bluetooth Go to system-off mode, sd_power_ramon_set can not be stored. In D: \ RAM save nrf51_sdk_v5_2_0_39364 \ nrf51822 \ Board \ nrf6310 \ s110 \ ble_app_rscs...
Hi,
Recently I want to set up a dynamic network that with the node change this position ,the network will change dynamically.But there is the question,with the node's position...
Dir Sir. I am checking the current profile of nRF24AP2 in RX mode.
After "open channel" command, I found the peak current at 10ms interval until connection pass.
How does...
Hello,
I am using Nordic's UART service to communicate with my project. I use iOS and also Master Control Panel (with a dongle) on a laptop.
I have two questions:
...
Hello, I'm a newbie who just started nordic. Please excuse me because I don't know many things.
I use nrf52DK board and SDK V17 and I am developing it using various ble_SDK...
Hi everyone,
I have developed a Zigbee application for the nRF52840 board and now I need to migrate to the nRF52833 board.
Are there any indications on how to proceed...
hi everyone, I am having a problem making the door sensor. I want to optimize the power of the sensor so after acting I will put the sensor in system_off mode. I have the...
Hi,
We were trying to flash the nrf modem firmware using the 'pynrfjprog'.
When only one nrf9160dk is connected , the flashing is success and no error.
But when multiple...
Hello, a question about this link:
https://infocenter.nordicsemi.com/index.jsp?topic=%2Fcom.nordic.infocenter.sdk5.v15.0.0%2Flib_bootloader_dfu_process.html
which says...
Hai,
We are using RTC in one of our project (in nrf52832).
RTC is working fine. I am waking up by every 30 mins once. But I am not able to configure same RTC instance...
I have an end device acting as a server, and I need to send data to a bound client. This is custom data, so I cannot use a reporting attribute. Basically I need to access...
Hi,
I am absolutely new to this DLMS and in the course of exploring some kind of opensource DLMS stack I came across this Gurux and fortunately NORDIC did some kind implementation...
Hi,
I am developing an ESB application with 1 central (nrf52832 DK) and several peripheral. The peripheral are nrf52832 + ICM 20948. Development is done with Segger embedded...
I am trying to setup development environment by following below steps.
The nRF Connect SDK Zephyr repository contains a list of required Python modules. Install these modules...
Hi,
I have bought NRF24LE1 module. Now I want to program the module. So, will anybody please suggest me which programmer should I use to write hex file ? I have mPro programmer...
Hi,
I am currently trying to implement a beacon scanner alongside peripheral mode BLE on an nRF52832. As I am only scanning for beacons, I was hoping I would not need to...
I have been trying to connect to 4G using iBasis and other vendor's SIM card but have not been successful.
I have the nrf9160 DK two years ago and have been sparsely trying...
Hi,
We have 4 NRF52833 DK being used for our development work.
Among that, 3 of them have stopped working and are not powering up.
They power up some times when connected...
Hi,
to develop a device driver in Zephyr for TI DAC80501, a 16-bit DAC, I2C interface,
I have to
1. add the dts child node under the i2c controller node
$i2c1...
