Hi, I have both the nRF8001 dev kit and the nRF51822 Eval Kit (EK). We are using the nRF8001 for most of our project with the BLE Arduino SDK. But I wanted to just load a...
Hi,
What is the suggested method to change a pending request, and make it earlier than previously requested, without closing and reopening the session?
For example,...
Hi,
I am using a custom pcb with a nRF51422 chip, and trying to setup ANT communication between 2 modules, but the sd_ant_channel_id_set call returns an invalid address...
Hi,
To use bidirectional continuous scanning mode in ANT, I have to transmit Extended Broadcast/Acknowledged/Burst messages using ANT Msgs 0x5D, 0x5E, and 0x5F (ANT Message...
We are preparing to get BT qualification for our product, developed with the 6 stack now, however want to update to 7 when it is finally released. A comment from the testing...
What is the best way to minimize transfer in progress errors when trying to send ANT messages? I am using the S310 stack on an nRF51422. I have a busy ANT channel that is...
I'm running into a weird timing issue with a nRF24L01+ which I'm not quite sure how to work around in the general case. The basic setup is two radios, A and B. Auto acknowledgement...
Hi
I have been trying to make a dual bank serial dfu bootloader with security features for nrf51822 (board 10028), but seems the UART/HCI dfu support is missing in SDK...
Hi,
I am having some trouble getting my design into low power.
I have a BLE central application using an nRF51822. I am using the power on sleep mode by calling sd_app_evt_wait...
Hi Nordic,
I have an application that perfectly runs in the nrf51DK but that does not work in my custom board. In my custom board everything else works (i2c, leds lighting...
I have a nRF51822 development dongle. I followed by the instruction and installed the USB friver, nRFGo Studio and Wireshark. All these software are installed a Win7(64bit...
Hello,
I am using ble_app_gls example and I have implemented static passkey in the code. Now I want to see if wireshark shows the passkey when I connect to ble devices. For...
What is the best way to go about implementing secure reads/writes to the NRF52 NFC tag? I noticed there didn't seem to be any built in security functionality in those areas...
I am attempting to use nrf_drv_adc.h in a project where I am splitting up my methods across many C files and, to my surprise, nrf_drv_adc.h does not have any include guards...
Hello,
I received the above error using NRF5 SDK 12.2. I have modified "nrf_drv_config.h" so that it reads #define TWI0_ENABLED 1 . Also, I put #include "nrf_drv_config...
Using nrf52 DK , SDK 12.2 , and armgcc.
I want to use BLE_UART but I also want to bond.
I started with the BLE_UART example code and added peer manager and FDS.
I...
I've been trying to track down a bug where a couple of my Central test devices, a Nexus 5 and 7 (Android 6.1), won't send a connection request to a peripheral they're bonded...
Hi
I have a problem on testing the HRS examples on SDK12.2.0.
When I use a android phone, running on version 6.0, using nRF Toolbox version 2.2.1 App, to connect to the...
Hi!
After reading nRF24L01 product spec, I'm really unsure:
Spec. says: "The input signal should not have amplitudes exceeding any rail voltage."
"rail voltage" it's...
Update 1/27/2016
Just reviewing again the pins + schematic; I am using the following pins:
SCK P0.07
CS P0.08
MOSI P0.06
MISO P0.05/AIN3
Looing at the...
