Dir Sir. I am checking the current profile of nRF24AP2 in RX mode.
After "open channel" command, I found the peak current at 10ms interval until connection pass.
How does...
Hello,
I am using Nordic's UART service to communicate with my project. I use iOS and also Master Control Panel (with a dongle) on a laptop.
I have two questions:
...
SWI*_IRQ is using by softdevice to send event to application, I want to know which priority does softdevice set for them?
Does sd_nvic_critical_region_enter() disable...
I am a started guy.
I only need a bluetooth device (BLE) to check the signal and mac address.
What is the best choice?
I need the smallest and low powered!
Thank you...
I am working on code to setup a bond manager for ancs based off of the example, but have a fixed advertising and connection interval of 25ms. How does the bond manager and...
Hello,
We have experienced odd problem, we are not able to scroll up or down SDK documentation at these pages on Android devices. IPHONE browser Safari works ok. Any help...
Based on nRF5_SDK_15.3.0_59ac345,
a. fds_stat(&stat), and stat.valid_records=8, It means that the records are written in
b. err = fds_record_find(WK_UDM_FDS_FILE, WK_UDM_FDS_REC_NAME...
Hello.
I'm running the nRF5 SDK's ATT_MTU throughput example.(nRF5 SDK v15.3.0, nRF52 DK(nRF52832))
The tester is running as a central or peripheral device.
How to operation...
Hi nordic moderator team,
I'd like for you to reopen this thread https://devzone.nordicsemi.com/f/nordic-q-a/51673/nrf52832-sd_ble_gatts_value_get-or-catching-ble_gatts_evt_rw_authorize_request...
Hi,
I am using APP UART for Communication with slave device, the data transmission between two devices like send a command and get the response,
while getting the response...
Hi,
I faced a problem while building my project. Please see screenshot below
I think I have already include all the files and everything compiled. But this error shows...
I am trying to run smart remote 3 on PCA10040/nRF52832.
I use gcc makefile to generate PCA63519-SR3_nRF52832_Shield firmware. SD firmware is downloaded by jflash and I use...
Hi,
I want to update firmware on nrf52832, but I have an error: DFU insufficient resources
I found this and this , so I try to program my softdevice with this file: /nRF5_SDK_15...
Hi，
there is a issue very strange, on a nrf52832 project, it use two gpio set to sense low level, one is p18, one is p29, I found there is no response for low level of p29...
We are using nRF52832 with SDK_15.3.0 running the Nordic UART service (NUS) example.
Out of the box we find that the uart event handler is continually being called with...
Hi,
I have an SPI peripheral on pins 26, 27, 28, 29 which I'm able to override the default system's UART0 pin assignments in nrf9160_pca10090ns.overlay. However when I enable...
Dear sir,
We have interfaced a charger ic with NRF52832. It is having a charging status pin to show completion of charge. It is having 3 states
1. High impedance (Battery...
Hello guys,
Something strange is happening here and I need your opinion about that... I have a custom board with nRF52840-based BL654 module on it. I am using SDK15.3.0...
Hello
I am using nrf52840 chip. I am having trouble configuring SAADC to read analogue input on two channels (one signal is VDD of the chip). I have already searched the...
I am trying to get connected with my Android App and I have noticed that sometimes when the user turns off Bluetooth and tries to enable it again after 20 minutes my Android...
