Using S120 V 8.0.0.3 alpha, processing a BLE_GATTC_EVT_READ_RSP,
received 0x16 bytes of data but there is more to read. Next call to
sd_ble_gattc_read using the same connection...
Hello：
Why Bluetooth Go to system-off mode, sd_power_ramon_set can not be stored. In D: \ RAM save nrf51_sdk_v5_2_0_39364 \ nrf51822 \ Board \ nrf6310 \ s110 \ ble_app_rscs...
Hi,
Recently I want to set up a dynamic network that with the node change this position ,the network will change dynamically.But there is the question,with the node's position...
Dir Sir. I am checking the current profile of nRF24AP2 in RX mode.
After "open channel" command, I found the peak current at 10ms interval until connection pass.
How does...
Hello,
I am using Nordic's UART service to communicate with my project. I use iOS and also Master Control Panel (with a dongle) on a laptop.
I have two questions:
...
SWI*_IRQ is using by softdevice to send event to application, I want to know which priority does softdevice set for them?
Does sd_nvic_critical_region_enter() disable...
I am a started guy.
I only need a bluetooth device (BLE) to check the signal and mac address.
What is the best choice?
I need the smallest and low powered!
Thank you...
Hi there,
My project needs TrustZone and ETB feature. The manual clearly states that the board supports TrustZone and ETM. I wonder if it also supports ETB to store trace...
Hi,
I am using SDK15.3 with the SoftDevice enabled. I've been unable to get any SoC events after making a call to sd_flash_page_erase. I registered my observer as follows...
I'm trying to develop a Bluetooth application where my Nordic nrf52 DK sends an event when I push the button and another when I release it.
I'm trying to apply this on the...
Folks,
One of the devs here found that all warnings were switched off in SES, so I've recompiled and got rid of most of the 1400 odd (sic) warnings by suppressing unused...
Hi
I want to use loggers in the program. I understand that the code itself uses NRF_LOG. But I do not understand where those log details are printed. So, how do I create...
I am experiencing an immediate BLE disconnect when trying to use DLE. I can write up to 20 bytes of data, but if I try to write more 21 bytes or more I get an immediate BLE...
I was wondering what I have to do to clear all stored mesh data on flash.
Do I have to initialize the whole mesh, or can I init only a subset?
What do I have to do so...
Hi all, I am working with NRF52840 and Open Thread SDK V3.1. Everything is normal.
But now, I want to run open thread example in SDK with NRF52811. T o reduce product costs...
Dear every one
I have a project with nRF52832 dev kit. I want it sleep (mode on) and wake up every 2 minute. When it wake up, it broadcast BLE and if it sleep it not broadcast...
I have a custom PCB that I designed for use with the nRF52811. I have tried to connect to it using the nRF Connect Programmer to program a Soft Device but I am unable to connect...
dear folks,
I bougth my dev kit last week from digikey. I tried the asset tacker demo out of the box without success. I tried nearly everything. Updated the modem to v1...
Hi,
Is it possible to use RTC for timekeeping along with app_timer functionality?
For example, I want to use simple RTC counter register and overflow interrupt to provide...
We are using ble app uart example in gcc. The uart event handler is not responding on APP_UART_DATA_READY. When it was build on keil it is working, but due to necessity we...
OS in development environment ：Windows7 HARD :(Taiyo Yuden)EBSHSN Series Evaluation Board : Central / Peripherals CPU :(Nordic) nRF52832 / ARMR Cortex-M4F 32 bit processor...
