Hi all,
I have an application where an nrf24le1 is communicating serially with another processor, using the UART at 57600 bps. I have multiple identical boards communicating...
after flash DFU program into pca10001 board, com3 is not accessible,
www.dropbox.com/.../Screenshot 2014-04-26 15.41.47.png
even after I erase all, and re upload soft...
Using S120 V 8.0.0.3 alpha, processing a BLE_GATTC_EVT_READ_RSP,
received 0x16 bytes of data but there is more to read. Next call to
sd_ble_gattc_read using the same connection...
Hello：
Why Bluetooth Go to system-off mode, sd_power_ramon_set can not be stored. In D: \ RAM save nrf51_sdk_v5_2_0_39364 \ nrf51822 \ Board \ nrf6310 \ s110 \ ble_app_rscs...
Hi,
Recently I want to set up a dynamic network that with the node change this position ,the network will change dynamically.But there is the question,with the node's position...
Dir Sir. I am checking the current profile of nRF24AP2 in RX mode.
After "open channel" command, I found the peak current at 10ms interval until connection pass.
How does...
Hello,
I am using Nordic's UART service to communicate with my project. I use iOS and also Master Control Panel (with a dongle) on a laptop.
I have two questions:
...
This maybe a stupid question but is there any reason to include support for older versions of the SDKs? I am using the pc-ble-driver approach and the example is full of if...
Is there any new information released about the GPS current consumption of nRF9160? I want to estimate the battery lifetime of a 1000mAh battery running the asset tracker...
Hi,
I am under long run test between coordinator and end device.
End device sends a message and goes into system off state until next event(door open) for minimal power...
Hi Everyone,
I am having problems writing to an array in NRF52832 without causing the program crashing at run time.
I declare the array to be 512 uint8_t long
then...
hi, I'm a fresher of this kind of development. My boss give me a board and let me run the Zephyr OS on it. But I am not sure whether I lack some things and how to assembly...
hello I am just needing some clarification on meshing. I am using the long range nfr52 chip. I have a transmitter with a tilt switch that connects to my receiver when connected...
Dear Support team,
could you please advice how can I change the endpoint where Thingy91 sends the measurement data stream from the sensors?
By the default it it is the...
HI, I'm Rafael Fajardo a student at Las Palmas de Gran Canaria University . I am using the nRF51 Dongle and following the Sniffer User Guide, but when I got to the final step...
Hello,
Zephyr has their own Bluetooth stack. Has anyone done an objective comparison of the Zephyr stack to the NRF52 soft device stack? I am very familiar with the soft...
Hi,
I'm currently making energy measurments with an nrf9160 DK. The software project is based on the udp_with_psm sample. I would like to run the test on different tx-power...
When debugging with Keil, the software may suddenly start from the beginning. The reset process may be running somewhere, but it cannot be detected. Is there information that...
Hi everyone,
I am a beginner developer, I'd like to know what's the difference between different softdevices.
In particular I am using SDK 10.0.0 with softdevice 110...
Dear Sir,
I am using Example beaconing_nrf52840_xxAA_s140_6_1_0 in nrf5 SDK for Mesh_v3.0.0 get stopped after running for sort period. I have tried to debug but could not...
Hi,
sd_ble_gatts_hvx returns 13313 in some rare cases involving the phone is far from the nrf52840.
My questions:
1. What this return code means?
2. What is the recommended...
