Hi all,
I have an application where an nrf24le1 is communicating serially with another processor, using the UART at 57600 bps. I have multiple identical boards communicating...
after flash DFU program into pca10001 board, com3 is not accessible,
www.dropbox.com/.../Screenshot 2014-04-26 15.41.47.png
even after I erase all, and re upload soft...
Using S120 V 8.0.0.3 alpha, processing a BLE_GATTC_EVT_READ_RSP,
received 0x16 bytes of data but there is more to read. Next call to
sd_ble_gattc_read using the same connection...
Hello：
Why Bluetooth Go to system-off mode, sd_power_ramon_set can not be stored. In D: \ RAM save nrf51_sdk_v5_2_0_39364 \ nrf51822 \ Board \ nrf6310 \ s110 \ ble_app_rscs...
Hi,
Recently I want to set up a dynamic network that with the node change this position ,the network will change dynamically.But there is the question,with the node's position...
Dir Sir. I am checking the current profile of nRF24AP2 in RX mode.
After "open channel" command, I found the peak current at 10ms interval until connection pass.
How does...
Hello,
I am using Nordic's UART service to communicate with my project. I use iOS and also Master Control Panel (with a dongle) on a laptop.
I have two questions:
...
hello,
inorder to send a string over ble from a slave to master or master to slave what is to be done??
is there any function for us to pass the string??
I want to understand the meaning of "standard drive, low frequency" GPIO pins. The datasheet mentions to use these pins for frequencies below 10 KHz. Does this limitation...
HI
I have to sending a sequence of 768(96 bytes) bits to program a custom piece of hardware on a single data line. Initially the line is low for 500ns and then each bit...
Hello. I'm testing ESB examples with nrf52832. Want to understand which max speed I can reach with that protocol? Some devzone info says that 1.8mbps can be reached. But among...
The assumption that `fds_record_find` returns records for NOT CHANGING file_id and record_key in the same order they have been written IS WRONG. The documentation sub-section...
Hello everyone,
we are developing a bluetooth application based on the relay example included in SDK 14.0.0. We have already developed our own services and characteristics...
We are working on a combination 52840/9160 board, and after having much success with most software components, have run into a roadblock with the more complex Bluetooth samples...
I am trying to create a custom board file in the ncs/zepher/boards directory for our nRF9160.
If I copy the nrf9160_pca10090 directory to a new nam eg. nrf9160_newboard...
I am using NSDK 15.3, MeshSDK 3.2.0, SoftDevice 6.1.1 and nRF52840 DKs.
Hello, I have followed the documentation for the DFU over mesh here and successfully upgraded a board...
Hi, 1. How soon a DK or something like that with an array of antenna to support the direction finding capability introduced in Bluetooth 5.1 will be available?
2. Provided...
Hi!
I am trying to use serial port library with Free RTOS (SDK 15.3). I created a read task but when I try to read, the function does sometimes receive wrong bytes. I also...
So I am trying to store a few configuration parameters in flash. I am using nrf_fstorage for that. so before storing the parameters, I am erasing the flash but, it hangs at...
I am using the chip NRF52840 ,the board is powed by a battery, and I program the firmware by using the JLINK,then I unplug the JLINK and waiting the system to go into sleep...
I'm working on a project using the nRF52840 that will have a central device with an NFC reader and up to three peripheral devices with an NFC tag. The goal is to have an LED...
We have already developed firmware for our product using SDK nRF5 SDK v14.2.0 with Soft device S132 V5.0.0. For the new product development, we plan to use the Soft device...
