I tried to do send & receive binary data from bluetooth in ios app.
But i only can send & receive string or ASCII code data in my app, do you have any method or idea can...
Hi,
I tried ble_app_hids_mouse with Android 4.4.2, it can work properly for first time connection. However, it cannot be re-connected after switching Phone's Bluetooth...
I have installed Keil MKD-Lite V 5.10.0.0 and the Segger software (which linked to the Keil IDE). I have tried to install the nRF51 SDK (5 times) and every time iI get the...
Hi,
I am attempting to get the DFU working as per the example provided in the S110 V7.0.0-3 download. I've followed all the steps in the readme in the DFU subfolder and...
Hi all,
I have an application where an nrf24le1 is communicating serially with another processor, using the UART at 57600 bps. I have multiple identical boards communicating...
after flash DFU program into pca10001 board, com3 is not accessible,
www.dropbox.com/.../Screenshot 2014-04-26 15.41.47.png
even after I erase all, and re upload soft...
Using S120 V 8.0.0.3 alpha, processing a BLE_GATTC_EVT_READ_RSP,
received 0x16 bytes of data but there is more to read. Next call to
sd_ble_gattc_read using the same connection...
Hi Nordic expert, I wanna get a profile of 51822 performance cycle count. I found 51822 has no powerful DWT feature as cm3 or cm4, would you share me some feasible methods...
Hi All
I am aware that there are some changes to UV5.12 to do with Device Pack location etc.
I have currently updated my project from the .uvproj to .uvprojx extention...
I was able to setup gazell communication between two devices one as device and other as host using 32 byte payload size in nRf51822 module.
Here in gazell communication is...
We are using the Nordic Semi nRF51822-QFAC on our device for BLE. Since we are developing from scratch I understand we need have FCC testing done. Is there a summary of the...
I'm devloping application on nRf51 for that i'm using... SDK : nRF51_SDK_7.2.0_cf547b5 Tool chain : GNU tools arm Embedded [arm-none-eabi version 4.9.3] Dev Board : PCA10028...
I'm trying to implement channel scanning in our nrf24lu1p based USB dongle.
I'm following the specs and basically loop though each channel ;
loop
stop listening
set...
I had a nRF81522 design that was working at 3.3V and I dropped the voltage to 1.9V. I didn't change anything else, but now I am getting periodic disconnects during interogation...
I have a PCA 10028.
This board uses Two microcomputers.
One is N51422.
Another is microcomputer on which the seal is put(Segger ID:).
What is the role of this microcomputer...
I recently discovered this article ( mbientlab.com/.../) and am trying to understand the data transfer type between the firmware ( ble_app_hrs_s110_pca10028 ) and an iOS device...
Hi,
Currently when I run the HRM demo I end up in the app error handler, unfortunately the error codes don't print to my terminal window. I'm using crossworks, and I was...
Hi,
I am new to using keil uvision. I am creating wearable solution, have enabled battery service indication, RTX support,bsp support, gpio,ble service.
When compiling...
Hello!
I would like to measure RSSI for different channels so as to decide which channel is the least noisy one (and more particularly, which ones are already used). I...
I am trying to choose a BLE device for my upcoming biomedical product design. Any help in comparing these 2 devices will be greatly appreciated.
Things I am concerned about...
Hi,
I am using the nRF51822 with an external chip. The nRF51822 has interrupts which trigger when one of the signals from the external chip goes low. When using BLE and...
