I have installed Keil MKD-Lite V 5.10.0.0 and the Segger software (which linked to the Keil IDE). I have tried to install the nRF51 SDK (5 times) and every time iI get the...
Hi,
I am attempting to get the DFU working as per the example provided in the S110 V7.0.0-3 download. I've followed all the steps in the readme in the DFU subfolder and...
Hi all,
I have an application where an nrf24le1 is communicating serially with another processor, using the UART at 57600 bps. I have multiple identical boards communicating...
after flash DFU program into pca10001 board, com3 is not accessible,
www.dropbox.com/.../Screenshot 2014-04-26 15.41.47.png
even after I erase all, and re upload soft...
Using S120 V 8.0.0.3 alpha, processing a BLE_GATTC_EVT_READ_RSP,
received 0x16 bytes of data but there is more to read. Next call to
sd_ble_gattc_read using the same connection...
Hello：
Why Bluetooth Go to system-off mode, sd_power_ramon_set can not be stored. In D: \ RAM save nrf51_sdk_v5_2_0_39364 \ nrf51822 \ Board \ nrf6310 \ s110 \ ble_app_rscs...
Hi,
Recently I want to set up a dynamic network that with the node change this position ,the network will change dynamically.But there is the question,with the node's position...
I want to operate
Tries to operate a small speaker.
www.wvshare.com/.../Analog-Test-Board.htm
but I can not find the DAC function in nrf51822.
How do I create...
Hello,
I am starting a project related with BLE communications. In the future, I want to design my own board and to be able to program it. I am going to start with a development...
Hi, all.
I have been using the nRF51822 board, I am making a peripheral.
The peripheral has been equipped with a sensor to multiple GPIO.
(For example, sensor1 to P0...
Hi
I am implementing my custom service, and started from the led/button example.
I am using the LightBlue app on my iphone to connect to my device under test.
I can see...
I am trying to generate the services.h file and get an error that "Something was wrong with the advertising packet". I see at the end of the log it says "Return code: 0x2...
Hello All,
I have a basic question about empty scan response operation with the ADV_IND PDU. When I set advertising data as follows:
err_code = ble_advdata_set(&advdata...
In the download section, all other SoftDevice versions are named "(Production ready)". Just the new S120 v2.0.0 is not. Does it offer the same stability/reliability as the...
We have an nRF51822-based product that goes the SYSTEM OFF in certain situations.
We wake up with the DETECT signal from a pin which we set to sensing just before calling...
I want to have it wireless capabilities into the cable, the receiver and transmitter antenna ports with shielded wire connected directly, so there will be a wireless signal...
Hello! I want to broadcast messages between 2/3/4/5/... devices. How Can I broadcasts between devices? Each device must receive messages from others and also broadcasts to...
Hi,
I'm unable to configure the UART so, that it will generate the TXDRDY event. I have an UART that should send periodicaly 4 Byte sequences without hardware handshake...
Hi,
For my research project on novel antennas I need a demonstration prototype, and the nRF51822 Beacon Kit would be ideal for me (due to its small size and battery power...
Hi there,
I was wondering it it is possible to use MATLAB as a central device, using a third party dongle?
The MATLAB Instrumentation Contol Toolbox can be used to control...
