Hi guys,
I am new to Nordic and I am using the evaluation kit "pca10001".
I have managed to run the LED BUTTON example which was declared in application note "nAN-36...
Hi,
I am having problem with the bootloader function of s110 v7. I am able to download the s110 softdevice. My application code was recompile with v7 header files. Able...
I am new to this forum and have some questions that I could not find elsewhere. The questions are:
Website asks me for a product key if I try to download the S210 soft...
Hi,
I'm starting to implement DFU using IAR's ARM workbench. In the example project for ARM that comes with the nrf51_sdk_v5_2_0_39364 SDK there is a file called bootloader_util_arm...
Do I have to use external host MCU for nRF51422? What can the ARM Cortex processor inside SoC 51422 do and cannot do?
I want to create a mesh network with hundreds of ANT...
Hi
I am looking at section 9.1 of the S110 Softdevice Specification v1.3A and the release notes for 7.0.0-2.alpha where I see that an application now starts at 0x15000...
Dear Nordic Community, I want to build samples/basic/blinkly on nordic nrf52840_dongle inside my Zephyr workspace. I use Zephyr 4.2.0, but on Zephyr 4.3.0 I have similar problems...
Hello, I am looking at pages 871 and 872 of the datasheet for the QFN48 package, but I’m not sure I understand correctly. Could you please tell me which GPIO P0 pins can be...
I’m using an nRF54L15 evaluation board obtained from a distributor and currently testing transmission and reception of large data chunks. Everything was working fine until...
I have an external device. After connecting it to the central device, I found that the Bluetooth service of my external device couldn't be enabled properly. When I checked...
Hi, I have the radio_test example running correctly on a nrf52840 dev board. I am able to use the Nordic Serial Terminal (v1.6.0) to send commands and read responses.
...
I am developing a custom board using nrf54l10 chip. So far, I have been able to use a code to comunicate through spi and uart for me to use printk function.
Now I was trying...
The docs( docs.nordicsemi.com/.../dect.html say that th nRF9151 modem can't do GPS/LTE and DECT NR+ at the same. Could the modem switch between the two operation modes while...
Hello team,
I am using SPI00 of NRF54L15 to communicate with w25q32fv (spi Flash). Below is the configuration I set in .overlay file
And below is the code I am using...
Hi,
I have a question about the the fields " tod_toa_reflector" and "toa_tod_initiator" in struct bt_hci_le_cs_step_data_mode_1.
I understand that these values represent...
The e-mail contains news of a new use of the nRF9151 module but uses the word "proves" and as an English language Cambridge qualified teacher I must mention that the word...
Issue description
I am using SAADC in single-ended mode with 3 channels (0/1/2). Measurements are performed by enabling SAADC, running offset calibration, configuring the...
Hello,
I have an application running on legacy NRF SDK and using the nRF5 bootloader, which has below flash sectors, 0x00000 - 0x026000 - Soft-device section 0x26000 - 0x0D9000...
Our custom product, based on the nRF52832, is undergoing certification. The testing laboratory requires that only one BLE advertising channel be active at a time—first channel...
Hi there,
We have a mass produced product with a modified secure bootloader (from SDK17). This BL has BLE and USB and we bolted on an SPI flash transport for OTA updates...
