Hi,
My behavior is as follows
Turn on my device(use 51422) and advertising(2 Service and 3 Characteristic)
Turn on my cell phone(Samsung Note3),scan my device...
Hello:
I used analog IIC write MPU6050. Again after power download programs, mpu6050 can run up there ACK response. But the debug will not run. Simulation IIC because no...
Hello!
How can I communicate with my nRF24L01+ and nRF51822 at the same time. I can set up same channel, CRC-mode and I don't use ESB. But what about address? How do I set...
Hi all,
i want to know answer related to following question
1)what is use of uicr?
2)if i place some value in uicr and then change the image,then is there will be change...
It used to work, but now it says "Connected" but the rest of the GUI never changes and the mouse just shows a busy spinner. Here's the log file:
0;13:45:18.9900 [MainThread...
Hi all!
My question is:
My own application is built based on the example "ble_app_template", and according to the nrf51 SDK - Examples - BLE Peripheral, this example...
Hi,
I am using ancs service to get some information of my iphone.
I use nRF51822 microcontroller and Nordic suggests to use the new SDK (5.2) for new microcontroller...
Hi,
I am using NRF51822 SDK12; S130 and trying to qualify Batter level service with the SIG's PTS device (dongle)
So far encountered a problem with Test Case: BAS/SR/DES...
Just got a nRF5340 DK, testing on macOS 10.15.2. Setup was smooth – the nRF Connect assistant is pretty good. The only feedback would be that an explanation of the "Variables...
Hello Nordic Team,
I'm currently working on a project based on the nRFready desktop. My application requires using the pipes 0-2: pipes 0 and 1 are used in conjunction with...
Hello everyone!
I want to use the app_sdcard to read/write with fatfs on a uSD card in my app which is based on FreeRTOS. While i was implementing this library, i saw that...
Hi,
I would like to know, where the packets are written into the flash for the mesh DFU example.
In nrf_mesh_dfu.c is a function nrf_mesh_dfu_cmd_send:
It calls...
Hello,
I have a little issue during the mesh configuration of my network.
First my provisioner (called master) provision and configure a first node (called slave), this...
I have downloaded project from https://devzone.nordicsemi.com/f/nordic-q-a/55710/while-building-thingysdkv210-on-segger-showing-error-thingysdkv210-source-modules-thingee_ble_handler...
I am using Nordic's nRF52840 DK board.
I wanted to sync time on End Device(nrf52840DK Board) via sending packets to it. What should I do?
what clock/rtc library or API...
I am sorry but this is totally BS. I just got the Thingy 91 and it does only problems...
I have no problem using a full day on getting stuff like that to work, but please...
I am currently developing a device and would like the default behavior at boot to be:
1. Boot up
2. The device should start advertising for non-bonded devices.
3. When...
Using the 15.3 SDK and the 6.1 software device I am successfully changing the transmit power as needed. When not connected and advertising I would like to update the advertised...
hi
i have a problem with 51822.
i test my production, power on /power off again and again.
maybe 51822 can not work. but is too hard happen.
My code is at main output...
I have customized the nrf toolbox app , facing the issues as below
1. I have created two pages , first page is used to scan and connect and second page is used to enter...
