Using S120 V 8.0.0.3 alpha, processing a BLE_GATTC_EVT_READ_RSP,
received 0x16 bytes of data but there is more to read. Next call to
sd_ble_gattc_read using the same connection...
Hello：
Why Bluetooth Go to system-off mode, sd_power_ramon_set can not be stored. In D: \ RAM save nrf51_sdk_v5_2_0_39364 \ nrf51822 \ Board \ nrf6310 \ s110 \ ble_app_rscs...
Hi,
Recently I want to set up a dynamic network that with the node change this position ,the network will change dynamically.But there is the question,with the node's position...
Dir Sir. I am checking the current profile of nRF24AP2 in RX mode.
After "open channel" command, I found the peak current at 10ms interval until connection pass.
How does...
Hello,
I am using Nordic's UART service to communicate with my project. I use iOS and also Master Control Panel (with a dongle) on a laptop.
I have two questions:
...
SWI*_IRQ is using by softdevice to send event to application, I want to know which priority does softdevice set for them?
Does sd_nvic_critical_region_enter() disable...
I am a started guy.
I only need a bluetooth device (BLE) to check the signal and mac address.
What is the best choice?
I need the smallest and low powered!
Thank you...
I am currently developing an HID over Bluetooth device and would like it to be able to determine which OS the host is running so then its beviour changes based on that info...
According to SIG specs the BLE Mesh max payload is = 384 ( 12 * 32)
nrf52 MAXLEN = 255 (but I can transfer 265 bytes in zephyr (259 bytes data + 2 bytes opcode + 4 bytes...
SDK version: nRF5_SDK_15.3.0
Platform: nRF52840 DK
SoftDevice: s140
--
Hi All,
I use blinky_freertos example to add nrf_serial lib to send/receive AT command by...
Hello! 1-st question - how can i set preprocessor defines using SES and NRF connect options? When i set define like: ARM_MATH_CM3 in proj.conf file, i get an error "malformed...
HI,
I am developing application based on healthcare. I am using nRF52832 with SDK15.3 in SES windows10.
I need to use bootloader DFU .
In my hardware i have only one...
I want to erase and write the flash while the BLE communication is going on.
In nRF52832 specifications it is mentioned that t he CPU is halted while the NVMC performs write...
Hello!
I want to use easyDMA. The SDK version I use is SDK15.0.I want to know how to config easyDMA.For example , If I only need to config TWI0_USE_EASY_DMA==1 ?
So far there are only a few devices that support Coded Phy. Is there any Bluetooth adapter that I connect (for example using OTG) to a smartphone (without built-in support...
SES will produce both hex and elf files when building. I can flash any old hex file with Target -> Download File -> Download Intel Hex File... But I can't actually have SES...
Hi,our product is ready for production and we are preparing commissioning software.
The 52840 is powered from a 3.7V LiPo via an external switching regulator that outputs...
Hi I managed to successfully implement a busy-wait using nrf_delay_ms(). However, I read that nrf_delay_ms() uses more power than app_timer's RTC. So I am trying to use app_timer...
Hi,
I am creating a central device with some similar services and code as the NUS example in the SDK. I posted with an issue here I was having earlier but I am writing this...
The recent update to nRF Connect 2.01 seems to have a problem with getting the firmware zip files into the inbox with iphone x max looks like the share option isnt putting...
I am a beginner trying to implement ble_app_uart example from SDK 15, example compiles with no problem, advertizes. LED 1 blinks when advertizing, and turns ON when connecting...
