I have installed Keil MKD-Lite V 5.10.0.0 and the Segger software (which linked to the Keil IDE). I have tried to install the nRF51 SDK (5 times) and every time iI get the...
Hi,
I am attempting to get the DFU working as per the example provided in the S110 V7.0.0-3 download. I've followed all the steps in the readme in the DFU subfolder and...
Hi all,
I have an application where an nrf24le1 is communicating serially with another processor, using the UART at 57600 bps. I have multiple identical boards communicating...
after flash DFU program into pca10001 board, com3 is not accessible,
www.dropbox.com/.../Screenshot 2014-04-26 15.41.47.png
even after I erase all, and re upload soft...
Using S120 V 8.0.0.3 alpha, processing a BLE_GATTC_EVT_READ_RSP,
received 0x16 bytes of data but there is more to read. Next call to
sd_ble_gattc_read using the same connection...
Hello：
Why Bluetooth Go to system-off mode, sd_power_ramon_set can not be stored. In D: \ RAM save nrf51_sdk_v5_2_0_39364 \ nrf51822 \ Board \ nrf6310 \ s110 \ ble_app_rscs...
Hi,
Recently I want to set up a dynamic network that with the node change this position ,the network will change dynamically.But there is the question,with the node's position...
Should it be possible to send SMS with the at_client example, and is there any special requirements to do so?
This is the AT commands setup procedure I've used:
AT+CFUN...
Can anybody help me please?
I'm trying to find a chip that will allow me to connect to my smartphone's internet connection over bluetooth.
I don't want to create an app...
I installed nRF connect for desktop in ubuntu 16.04. I added Programmer app . It was working fine till yesterday. But I update it from the nRF connect today. But now programmer...
Hello,
I try to use the opus codec on an 52840-DK. The Build and Flash with ARMGCC woks fine (with gcc-arm-none-eabi-8-2019-q3-update) but I'd like to use the debugger from...
While using the Zigbee OTA examples (nRF Thread and ZigBee SDK v3.1.0), I have noticed by the sniffer, that the attribute “Block Request Delay” is presented in the OTA Upgrade...
Hi! A strange problem we encountered is a different behavior of our boards before and after cutting the SB40 bridge and place a jumper on P22.
First part which works as...
Hi,
We are using NRF52840 DK in our project.I am using keil5 uvision, using SDK 15.3.0 and soft device S140.I have installed nrfx command line tool version 10_3_0 and nrfgo...
I'm using Segger Embedded Studio 3.52, nRF SDK for Thread and Zigbee v3, nRF52840-Preview-DK
I have a Zigbee Coordinator and Zigbee Router that work great at my home office...
I can success transplant saadc and fatfs to my ble project.However, when there is a SD card, the slave can write data to SD card successfully, but disconnect with the master...
Hi engineers, I got a question regarding nRF52840 (PCA10056), i want to run DTM using PCA10056 board with MT8852B tester. Unfortunately, i keep failing to get the EUT address...
Dear all,
Our application is made of
Chip nRF518122 + SDK 11.0.0 + DFU Bootloader + BLE application (gcc complied) loaded with nRF Toolbox over the air
we are putting...
Hello,
the nRF9160 product specification 1.0 states in 5.1.4.2:
"Note: The LTE modem requires using LFXO as the LFCLK source."
I checked the clock register and noticed...
Hi,
I have developed an SWD working code which read-write the Flash Memory and RAM which is working very good.
Now I have a problem in I need to write start address...
Due to time pressure, I'm starting this thread based on an existing ticket: https://devzone.nordicsemi.com/f/nordic-q-a/51423/firmware-on-custom-board-application-bootloader...
